aggie Posted April 27, 2020 Report Share Posted April 27, 2020 Hello, I am just about to recover ( retrim ) the rear wheel arches of my Spitfire 4. Have cleaned everything and cut the new material roughly to shape but, because the arch is arched and the material is flat it's a bit like wrestling with an eel. Anybody out there done this before and got any helpful tips such as where to start i.e. top, bottom or middle ? Link to comment Share on other sites More sharing options...
dougbgt6 Posted April 27, 2020 Report Share Posted April 27, 2020 Aggie, I've replaced my GT6 carpets, all except the wheel arches, not looking forward to it for the same reasons as you! I bought a loose carpet set, the wheel arch pieces have 3 narrow "pizza slices" about 3" long cut and stitched up. This gives curvature on the top of the arch. A similar thing has been done on the gearbox tunnel carpet but too much material has been left and I've had to pack under the carpet with seating foam, looks OK. I may have to do the same to the wheel arches. Good luck, tell us how you get on. Doug Link to comment Share on other sites More sharing options...
Colin Lindsay Posted April 27, 2020 Report Share Posted April 27, 2020 Is it carpet or vinyl, Aggie? I've just replaced the Gt6 arch carpets and they ended up looking like the original baggy trousers, but thankfully most of it is hidden. I stuck the flat faces first then curved and stuck the carpet an inch at a time, using heavy magnets from old speakers to keep it in place whilst the glue dried. For the Herald they supplied vinyl-like material and it's a matter of starting in the centre then with lots of heat and contact adhesive smoothing the stuff out towards the edges, like vinyl-wrapping a car. Link to comment Share on other sites More sharing options...
NonMember Posted April 27, 2020 Report Share Posted April 27, 2020 The professional (expert) trimmer who fitted my Spitfire's interior cut those wheel arch vinyl pieces and sewed them up to shape. It's a neat job but I don't think the originals had the stitched seam. Link to comment Share on other sites More sharing options...
aggie Posted May 9, 2020 Author Report Share Posted May 9, 2020 Thankyou all. Think i'll go with your method Colin. Any particular glue that you use ? I've used several different spray adhesives when fitting carpet and odd bits of trim but don't really rate any of them too highly. Link to comment Share on other sites More sharing options...
Colin Lindsay Posted May 9, 2020 Report Share Posted May 9, 2020 4 hours ago, aggie said: Thankyou all. Think i'll go with your method Colin. Any particular glue that you use ? I've used several different spray adhesives when fitting carpet and odd bits of trim but don't really rate any of them too highly. Aerosol contact adhesive; no idea of the brand but it was marked Heavy Duty. Link to comment Share on other sites More sharing options...
daverclasper Posted May 9, 2020 Report Share Posted May 9, 2020 (edited) Never used the aerosols, though Evo Stick contact adhesive (£4.50 from Screwfix for a smaller tin) seems very good. Maybe not for large areas, as takes a bit of time to spread and surfaces need to be pressed together after 5+ mins or so. The various brand smaller tubes, don't seem any good any more?. Edited May 9, 2020 by daverclasper Link to comment Share on other sites More sharing options...
dougbgt6 Posted May 9, 2020 Report Share Posted May 9, 2020 The aerosols, don't smell at all, not like Evo Stick, which some might find disappointing. Also I think they're not so strong, I had to remove a vertical section of my carpet which had been liberally sprayed, but came off quite easily. I'm going to try the aerosol on my wheel arches, but I suspect doing it the "Lindsay" way may need something stronger. Doug Link to comment Share on other sites More sharing options...
Black Cat Posted May 14, 2020 Report Share Posted May 14, 2020 Woolies do a Hi-Flex Lining Carpet Quote from Wolies: - "Soft, very flexible, unbacked, 4 way stretch roof and sidewall lining carpet. Useful for shaping and mouding around tight corners like wheel arches and window recesses. I've seen this used in a camper van it it conformed to all the in and out shapes and looks very professional and at £19.50 for a 1000mm x 2000mm wide not too expensive. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now