johny
-
Posts
7,671 -
Joined
-
Last visited
-
Days Won
44
Content Type
Profiles
Forums
Blogs
Gallery
Downloads
Store
Events
Posts posted by johny
-
-
Hi, Im not sure what work they carried out but that seems a lot of money!
The idle smoothness of any engine is dependant on quite a few factors so unless you're certain other adjustments such as tappets, carb balance etc are correct the best thing would be to check those first. There can also be air leaks or wear in the carburettors themselves which will also make it very difficult to get a smooth tick over however the good news is that the adjustment itself is very easy.
Our cars as standard are fitted with very simple carbs where the accelerator pedal just operates a butterfly valve in each carb to increase the amount of fuel/air mix going to the engine. The tickover setting is purely achieved by holding these butterfly valves open a little when the pedal has been released and this is done by a screw on each carb butterfly operating mechanism. They should be easy to see if you locate the accelerator cable (which must be slightly slack) and need to be undone a little and by the same amount on each carb while the engine is running and hot.
If you cant maintain a stable tick over at about 900rpm then you will need to look at some of the other factors that I mentioned earlier....
-
That doesnt sound like the standard set up and the filter could be blocked. Dont forget that if the vent is connected to the inlet manifold any gases are sucked out of the crankcase but of course even then if the flow is too much it will affect the fue/air mixture going to the engine....
-
-
of course, yours is the rotaflex isnt it so different design. I think with the early design the only remedy is to take out the bolt every so often and re-lube it....
-
a good idea but surely that would lubricate the stainless tube/bush not between the tube and bolt? Maybe the oil manged to flow round the end of the tube - did you use end seals?
-
Gawd whats the answer then? Stainless bolt that might snap under load.....
-
39 minutes ago, Nick Jones said:
Cold start thrust will be largely unlubricated though..........
most moderns have full circle thrust washers though - and formed as part of a main bearing shell too so they can't fall out.
Nick
unlubricated especially as now modern oil is like water....
-
the thrust generated by the clutch is the reason I dont understand why some modern cars now require the clutch to be operated before starting - surely this is the quickest way to finish off the thrust bearings?
-
Good service indeed! Let us know how it drives when its all bolted back in?
-
The only reason for leaving out the shields and seals would be when the tubes the bushes run on are stainless so will not rust (the seals arent designed to protect the bolt which not being stainless should be covered with an anti-corrosion lubricant).
-
I doubt that these components are interchangeable and as I said previously cant see that the spring length alone will make much difference to wheel camber. It sounds to me that, assuming the spring is correctly mounted, you have one that has had an easy life and not flattened out much. However if youre worried about the positive camber (not so much of a problem with a swing spring car) then as Clive says a lowering block or more tools/spares in the boot will help correct it.
- 1
-
dont forget that although the angle of the vertical link may change this is independant from the trunnion angle (because its free to rotate on its bushes) so the angle of the wheel depends purely on the angle of the half shaft. The flatter (softer) or higher (raising block) the spring the shallower the angle of the half shaft becomes and the more negative the wheel camber.
-
your right Doug, of course the nipple is in the vertical link and the oil is pumped out of the hole in the bottom of the threaded section where it then pools inside the trunnion.
I believe Paul has mixed up the names of the vertical link and trunnion....
-
dont understand Paul - theres a hole in the vertical link? and how does oil get out as it should be sitting trapped in the threaded section of the bronze trunnion?
-
7 minutes ago, NonMember said:
On the face of it, without any deep thought or consideration of mechanical engineering, perhaps. But the bottom trunnion holds the weight of the car in tension. Ball joints are actually not a very good design for that. You'll note the Dolomite, which does have ball joints top and bottom, also has the spring on the top wishbone, so the joint that takes the weight is in compression. Much more surface area available that way.
That sounds reasonable given that the bronze threaded trunnion was actually patented by Triumph so they must have put some serious thought into it!
-
ahhh I have a theory! On some cars disc brakes on the rear would be too powerful (the hub limits how small a disc can be fitted) so to avoid having to have a hydraulic compensator they use drums which are obviously less effective but matches the demands of the vehicle design....
-
yes but they used a ball joint at the top so logic would dictate that you could use the same item at the bottom! I cant believe that a bronze casting with bushes plus machined screw thread on the upright (which needs filling with gear oil every 3000 miles) was cheaper than a ball joint and taper.....
-
I never understood why Triumph went for the bottom trunnion design as surely it wouldnt have been more expensive to have an additional ball joint at the bottom. It would have solved all the problems of wear, play and routine maintenance and is what was used by other manufacturers in later designs.....
-
If its one of the chinese examples it might need a bit of fettling as it was probably made using only a photo of an engine bay....
- 1
- 1
-
Best go electric, he says opening the can of worms?
-
18 minutes ago, JohnD said:
I very, very, very much doubt it.
I don't know when Triumph introduced the plastic fan, but China around 1960 was just beginning the Cultural Revolution. The Great Leap Forward had concentrated on heavy industry, producing pig iron in villages and ruining agriculture, leading to the Great Famine that killed as many as 40 Million people. This failure meant that a new revolutionary movement was necessary, hence the CR, the Litttle Red Book, Red Guards etc etc. Even if it was capable, China had far too many problems to think about making goods for Imperialist running dogs!
Japan is possible, but we did not have a global industrial transport system in those days. Raw materials and complete products would be exported/imported, but parts would be sourced from local or national suppliers, not from halfway around the world!
History and a knowledge of history, are so important. "Those who do not know history's mistakes are doomed to repeat them."
John
Reading the post is also very important. "Those who dont read correctly the posts are doomed to make mistakes"?
- 2
-
I suppose cost also came into the decision back in the day - the plastic jobbies must have been so much cheaper although I bet they werent originally made in China?
-
yes even with SS I think the bolt will seize in the tube but at least the bushes shouldnt be damaged by rusting of the tube which finishes em off in double quick time....
-
think the seals are only intended to protect the tube and the bolt takes its chances (presumibly its galvanised or something). So with a stainless tube no need for seals and the bolt wont be any worse off...
Rear Trunnions
in Chassis, Suspension & Steering
Posted
+1 for using a syringe to oil front trunnions (sometimes it helps to push in the little ball in the nipple first to ensure its not seized)....