johny Posted April 21, 2021 Report Share Posted April 21, 2021 yes thats the correct one for your car so if a gearbox designed for a 3.89 diff ratio has been installed you will have a speedo which under reads by about 4 mph at 3000rpm (assuming perfect speedo and tacho calibration). Unfortunately the gearbox number cant be seen wthout removing the interior cover... Link to comment Share on other sites More sharing options...
Pete Lewis Posted April 21, 2021 Report Share Posted April 21, 2021 to get the turns per mile ( TPM) mark out 52.8ft down the road undo speedo cable from the back of the speedo stick a card needle on the drive cable push/drive the car accurately the 52,8ft count the turns on the needle multiply turns by 100 = the TPM eg a 1000 tpm speedo should give you 10 turns of the needle (revolutions of the cable) Link to comment Share on other sites More sharing options...
johny Posted April 21, 2021 Report Share Posted April 21, 2021 Right and I calculate if a 3.89 gearbox has been installed you'll only get about 9.3 revolutions of the cable over that distance.... Link to comment Share on other sites More sharing options...
cliff.b Posted April 21, 2021 Author Report Share Posted April 21, 2021 I may be confusing myself here but surely if the gearbox was from a car with a 3.89 diff and my car has & 3.65 diff then the Speedo would read too fast, not slow. For a given road speed with the 3.89 diff the gearbox output would make a certain number of revolutions. If the diff was changed to 3.65 then the gearbox & Speedo drive would turn faster for the same road speed. Link to comment Share on other sites More sharing options...
GrahamB Posted April 21, 2021 Report Share Posted April 21, 2021 With a 3.98 diff for every 3000revs in top gear, the wheels will revolve 771 times. Assuming a rolling circumference of 6 feet, the car will travel 1542 yards or 0.876 miles. So at 3000 rpm the car will travel at 52.6 mph giving a overall gearing of 17.5 mph / 1000rpm. With a 3.65 diff the wheels will revolve 3000/3.65 = 822 times and the car will travel 1644 yards or 0.934 miles. So at 3000rpm the car will travel at 56 mph giving an overall gearing of 18.7 mph/1000rpm. Therefore changing from the intended Dolomite diff to a Spitfire will cause the speedo to under-read . To correct the reading, assuming it was correct in the first place, you need to multiply the mph by a factor of 1.066 I knew that the A level in maths and mechanics would come in useful one day ! Link to comment Share on other sites More sharing options...
johny Posted April 21, 2021 Report Share Posted April 21, 2021 Yes Graham has got it. Although youre not changing diffs in this case you could think of your car as a 3.89 that has had a 3.63 diff fitted... Link to comment Share on other sites More sharing options...
cliff.b Posted April 22, 2021 Author Report Share Posted April 22, 2021 6 hours ago, GrahamB said: With a 3.98 diff for every 3000revs in top gear, the wheels will revolve 771 times. Assuming a rolling circumference of 6 feet, the car will travel 1542 yards or 0.876 miles. So at 3000 rpm the car will travel at 52.6 mph giving a overall gearing of 17.5 mph / 1000rpm. With a 3.65 diff the wheels will revolve 3000/3.65 = 822 times and the car will travel 1644 yards or 0.934 miles. So at 3000rpm the car will travel at 56 mph giving an overall gearing of 18.7 mph/1000rpm. Therefore changing from the intended Dolomite diff to a Spitfire will cause the speedo to under-read . To correct the reading, assuming it was correct in the first place, you need to multiply the mph by a factor of 1.066 I knew that the A level in maths and mechanics would come in useful one day ! Yes, you are absolutely correct and what I wrote was the opposite of correct. In my defence I had drunk more than several beers when I wrote it 🥴. Link to comment Share on other sites More sharing options...
cliff.b Posted April 22, 2021 Author Report Share Posted April 22, 2021 6 hours ago, johny said: Yes Graham has got it. Although youre not changing diffs in this case you could think of your car as a 3.89 that has had a 3.63 diff fitted... Link to comment Share on other sites More sharing options...
cliff.b Posted April 22, 2021 Author Report Share Posted April 22, 2021 Yes, I agree, Graham has got it. Please see my response to him to understand why I said otherwise lol. Also agree with your simplified explanation although as my Speedo is reading 15% slow, I am thinking it would need to be like putting a 3.63 diff in a 4.11 car? Also, I have noticed that if I shift into 1st gear just before stopping at a junction the box crunches a little, leading me to think it might not have synchro on 1st & from an earlier car. I will have to get out of the habit. Link to comment Share on other sites More sharing options...
johny Posted April 22, 2021 Report Share Posted April 22, 2021 Your right that the error is pretty big but theres some reasons why it would be surprising if an early gearbox (and it would have to be very early to be only 3 synchro) had been installed: Yours should be a single rail which only came in 3.89 and 3.63 flavours and all of them 4 synchro. This type can be confirmed by the position of reverse on the gear lever which should be lift, right and forward? The earlier 3 rail has reverse on the left and is an inch shorter so a making a swop a bit more complicated. Our theory is that the earlier boxes all had the same speedo drive gears and the correction was done in the speedo itself. A crunch on selecting a gear can be due to a worn synchro, dragging clutch and/or high tickover and is not unusual in first. Link to comment Share on other sites More sharing options...
cliff.b Posted April 22, 2021 Author Report Share Posted April 22, 2021 48 minutes ago, johny said: Your right that the error is pretty big but theres some reasons why it would be surprising if an early gearbox (and it would have to be very early to be only 3 synchro) had been installed: Yours should be a single rail which only came in 3.89 and 3.63 flavours and all of them 4 synchro. This type can be confirmed by the position of reverse on the gear lever which should be lift, right and forward? The earlier 3 rail has reverse on the left and is an inch shorter so a making a swop a bit more complicated. Our theory is that the earlier boxes all had the same speedo drive gears and the correction was done in the speedo itself. A crunch on selecting a gear can be due to a worn synchro, dragging clutch and/or high tickover and is not unusual in first. Ok, reverse is right and forward so that confirms it's not an early box I guess. Maybe I'm just trying to engage 1st at too high a speed or not fully depressing the clutch. Thanks for the clarification 👍 Link to comment Share on other sites More sharing options...
Pete Lewis Posted April 22, 2021 Report Share Posted April 22, 2021 reverse to the right is a single rail box correct for a 1500 spit Im just rebuilding a 3 rail from a GT6 been off the road for 30 years all baulk rings worn out and the constant clashing of teeth when it was on the road has wrecked most of the dog tooth chamfers, a classic case of clutch not clearing most have no idea what goes on with synchromesh , its driven from the mainshaft and in the blink of an eye the rings have to have 1/2 tooth misalinment ( rock over)to baulk the change till its spun the clutch disc up /down to match then the ring allows the sleeve to progress to lock the dog teeth any clashing/crashing chimbles the dog tooth chamfer angles to end up as a scrap gear or hub here is a Rootes take on explaining it all so lesson is do not clash /crash selections Link to comment Share on other sites More sharing options...
cliff.b Posted April 22, 2021 Author Report Share Posted April 22, 2021 5 hours ago, Pete Lewis said: reverse to the right is a single rail box correct for a 1500 spit Im just rebuilding a 3 rail from a GT6 been off the road for 30 years all baulk rings worn out and the constant clashing of teeth when it was on the road has wrecked most of the dog tooth chamfers, a classic case of clutch not clearing most have no idea what goes on with synchromesh , its driven from the mainshaft and in the blink of an eye the rings have to have 1/2 tooth misalinment ( rock over)to baulk the change till its spun the clutch disc up /down to match then the ring allows the sleeve to progress to lock the dog teeth any clashing/crashing chimbles the dog tooth chamfer angles to end up as a scrap gear or hub here is a Rootes take on explaining it all so lesson is do not clash /crash selections Indeed. I'm trying to get back into the habit of being nice to the gearbox by blipping the throttle during a down change to match engine to road speed. Something I haven't done for a long time. Link to comment Share on other sites More sharing options...
johny Posted April 22, 2021 Report Share Posted April 22, 2021 I think maybe your box is a bit tired because yours will have the later bigger synchro rings which should be more effective than the original type in mine. With the torque of the six plus a weaker bearing design you can imagine how gentle I am with it although its true gear changes are less frequent as I get it into 4th asap and pretty much leave it there... Link to comment Share on other sites More sharing options...
cliff.b Posted April 22, 2021 Author Report Share Posted April 22, 2021 28 minutes ago, johny said: I think maybe your box is a bit tired because yours will have the later bigger synchro rings which should be more effective than the original type in mine. With the torque of the six plus a weaker bearing design you can imagine how gentle I am with it although its true gear changes are less frequent as I get it into 4th asap and pretty much leave it there... I will try and treat my box with respect, hopefully that will come naturally as I drive it more. But if and when it's time does come I would probably take the opportunity to fit overdrive. Hopefully that won't be too soon as I have enough things to do already 🙄 Link to comment Share on other sites More sharing options...
johny Posted April 22, 2021 Report Share Posted April 22, 2021 of course the other thing to take into account is that materials and machining tolerances have moved on a lot since our boxes were manufactured. Current synchro rings and gears are made of metals that better resist wear and are lighter so spin up much more easily during the synchronisation process giving faster and possibly smoother changes. You have to alter your style when driving our cars and work at it a bit more but I think thats part of the enjoyment👍 Link to comment Share on other sites More sharing options...
cliff.b Posted April 22, 2021 Author Report Share Posted April 22, 2021 58 minutes ago, johny said: of course the other thing to take into account is that materials and machining tolerances have moved on a lot since our boxes were manufactured. Current synchro rings and gears are made of metals that better resist wear and are lighter so spin up much more easily during the synchronisation process giving faster and possibly smoother changes. You have to alter your style when driving our cars and work at it a bit more but I think thats part of the enjoyment👍 Yes, I agree. It used to be second nature driving these cars and it will be again. I think there is a need for a degree of "mechanical sympathy" that modern vehicles don't need, although they also benefit from it if shown. Link to comment Share on other sites More sharing options...
Pete Lewis Posted April 22, 2021 Report Share Posted April 22, 2021 3 hours ago, cliff.b said: blipping the throttle during a weve all done this but in reality this does allow the baulk rings to let go as the rock over process is lost Pete Link to comment Share on other sites More sharing options...
cliff.b Posted May 18, 2021 Author Report Share Posted May 18, 2021 Just a bit of feedback after a month or so. Today I took the car out for a reasonable distance, setting the trip to zero & taking my phone with GPS app. The Speedo still reported about 15% below the GPS but the distance travelled was almost exactly the same on both. From this I am concluding that, as already ascertained, the diff, the gearbox speedo takeoff and the Speedo itself are all the correct parts, but the Speedo is not correctly calibrated for speed. Link to comment Share on other sites More sharing options...
johny Posted May 18, 2021 Report Share Posted May 18, 2021 That sounds reasonable especially as the needle's magnet/disc mechanism and bearings will almost certainly have seized up bit over the years. In fact you could even try opening it up for a clean and lube as that part is easy... Link to comment Share on other sites More sharing options...
cliff.b Posted May 18, 2021 Author Report Share Posted May 18, 2021 36 minutes ago, johny said: That sounds reasonable especially as the needle's magnet/disc mechanism and bearings will almost certainly have seized up bit over the years. In fact you could even try opening it up for a clean and lube as that part is easy... Yes, I might have a look at that once/if I get everything else sorted out. In fact the Speedo will have to come out at some point because I will need to do something with the dash. Wood effect sticky back plastic at the moment 😒 Link to comment Share on other sites More sharing options...
johny Posted May 18, 2021 Report Share Posted May 18, 2021 I expected to find some means of adjusting the distance between the magnet and disc but couldnt see anything. However it was worth cleaning everything with a artist brush and lubing with a penetrating oil... Link to comment Share on other sites More sharing options...
Pete Lewis Posted May 18, 2021 Report Share Posted May 18, 2021 if the speed errors are constant you could remove the mechanism hold the rear disc and just gently move the needle round bear in mind it must read fast it must not read slow it may take a couple of tests to get it closer ,to what you want it to read the hardest job is freeing the glass from its degraded gooey sealing 0 ring rubber Pete Link to comment Share on other sites More sharing options...
cliff.b Posted May 18, 2021 Author Report Share Posted May 18, 2021 1 hour ago, Pete Lewis said: if the speed errors are constant you could remove the mechanism hold the rear disc and just gently move the needle round bear in mind it must read fast it must not read slow it may take a couple of tests to get it closer ,to what you want it to read the hardest job is freeing the glass from its degraded gooey sealing 0 ring rubber Pete It's out by a pretty much fixed % across the speed range. I found some stuff about calibrating speedos but that involved changing gears. Obviously, as the odometer is correct that isn't the problem. It then went on about unsoldering the needle hair spring and adjusting that way but even if I considered doing that, how on earth would you get it right. Will probably try the cleaning/lubricating at some point, as suggested, or send it away for repair. Or now that I know what the problem is, find a replacement. Link to comment Share on other sites More sharing options...
johny Posted May 18, 2021 Report Share Posted May 18, 2021 I thought the needle was pretty well fixed - it certainly didnt want to come off easily and I didnt want to force it as thought it might upset the disc to magnet distance... Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now