Stratton Jimmer Posted May 8, 2022 Report Share Posted May 8, 2022 The Sixfire has a fibreglass bonnet and had been fitted with twin gas struts which made raising or lowering the bonnet an absolute doddle. Only snag is that there was no gap between the bonnet and car when it was lowered. Removed the covers and found the adjuster was fully back. Slackened them off and tried to move the bonnet but it just moved back. In essence, the twin struts were too powerful for the adjuster. I took one of the struts off leaving just the nearside one on and hey presto, the bonnet is now adjusted with a nice panel gap. Be wary if fitting twin gas struts! Link to comment Share on other sites More sharing options...
Pete Lewis Posted May 8, 2022 Report Share Posted May 8, 2022 with the bonnet tube there is a risk it gives a bit under the load of the struts one good reason triumph never used the lever and spring idea of the H & V cars Pete Link to comment Share on other sites More sharing options...
Badwolf Posted May 8, 2022 Report Share Posted May 8, 2022 I got a pair of gas struts for the spit ages ago (don't tell Kevin, he hates them) ready for when I finished my steel bonnet....ok, stop laughing at the back!!! I didn't put them on the glass fibre bonnet in case they ripped it to bits. Maybe I should give them it a try. Link to comment Share on other sites More sharing options...
Neil Clark Posted May 13, 2022 Report Share Posted May 13, 2022 Just for interests sake, is the fibreglass bonnet very much lighter than the steel? And does it flex as much when lifting it from one side, as we must? Link to comment Share on other sites More sharing options...
Pete Lewis Posted May 13, 2022 Report Share Posted May 13, 2022 last time i lifted a FG bonnet i needed extra shreaded wheat it was very heavy but lb for lb i have no idea about the bonnet weights you really need one lifter each side to prevent stresses pete Link to comment Share on other sites More sharing options...
Badwolf Posted May 13, 2022 Report Share Posted May 13, 2022 My MkIV spitfire fibreglass bonnet is very wibbly, wobbly when lifting. Fairly solid when latched down. Like a sail when vertical. I much prefer the steel but, as followers of my restoration trivia stuff know, we don't talk about that!! Link to comment Share on other sites More sharing options...
Stratton Jimmer Posted May 16, 2022 Author Report Share Posted May 16, 2022 I am going to investigate what the spec is for the gas struts as fitted. They are obviously too strong for the FG bonnet so ideally a pair of weaker struts should do the job. I will post more as my investigations continue. In the meantime, one strut does seem to do the job reasonably well. Link to comment Share on other sites More sharing options...
Badwolf Posted May 16, 2022 Report Share Posted May 16, 2022 Might give single lift as go then, maybe on the opposite side to the side that I normally lift from, which is the side of the standard support thingie. Link to comment Share on other sites More sharing options...
Stratton Jimmer Posted August 5, 2022 Author Report Share Posted August 5, 2022 The single strut has been working really well so I have decided to stick with it. The struts as fitted were Metrol Springs NS-FF-8-300 rated at 360 Newtons. I looked on their web site and they don't actually list a 360N one but do list a 350N. The part number indicates that it is an 8mm rod with 30cm travel. https://motioncontrol.metrol.com/fixed-force-gas-strut-ns-ff-8-300-s.html These are clearly too strong for the fibreglass bonnet and as one does a good job (albeit asymmetrically as per the original bonnet support) I will suggest that a force rating of 150N should be perfectly adequate if using a pair. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now