68vitesse Posted January 15, 2017 Report Share Posted January 15, 2017 I have been changing the suspension bushes on my Vitesse to polyurethane, a well known make, all have fitted ok up to now. The front upper shock absorber bush as fitted is to big to go through the hole in the front turret. My option seem to be as follows. Fit it back and see if the weight of the car pushes it through, I do not feel it would be a good idea to try and pull it through with the three top plate studs as they are quite small. Remove the turret and enlarge the hole, there would be plenty of metal left to support the top plate. The number cast onto the bush shows it has been correctly supplied. As this is a common upgrade I do not feel I am the only one to have this problem, or is it a challenge these days?. Regards Paul Link to comment Share on other sites More sharing options...
Pete Lewis Posted January 15, 2017 Report Share Posted January 15, 2017 Any chance of a photo? the weight wont do much you are only looking at the shocker spindle damping loads the shocker only loads this bush when fully extended on a jack etc? On the floor there is no load on the shaft Dont leave it hanging off a jack you need the suspension semi loaded or the shocker will seem too short Have you tried fit the cup washer and underside bush and raise the shaft through it then fit the top bush and cup washer pete Link to comment Share on other sites More sharing options...
68vitesse Posted January 15, 2017 Author Report Share Posted January 15, 2017 The only way to fit as you suggest would be to use hook type spring compressors, I do not have any as have never trusted them. Refitting the shock absorber then jacking up under the bottom wishbone might push the top bush through the turret hole as it is above the spring top plate. Regards Paul Link to comment Share on other sites More sharing options...
Colin Lindsay Posted January 15, 2017 Report Share Posted January 15, 2017 The bush should fit through ok, have you compressed it so much that it's pancaked out? Link to comment Share on other sites More sharing options...
68vitesse Posted January 16, 2017 Author Report Share Posted January 16, 2017 Always thought the amount of compression was set by the length of the threaded portion of the top shock absorber stud. Regards Paul Link to comment Share on other sites More sharing options...
dougbgt6 Posted January 16, 2017 Report Share Posted January 16, 2017 I don't think the bush is supposed to go through the hole. Rimmer's diagram, below shows two bushes, one above the plate and one below. http://www.rimmerbros.co.uk/Item--i-GRID007841 The kit from the club shop has four bushes, two per side? https://shop.tssc.org.uk/product/front-suspension-polybush-kit-1116-anti-roll-bar-0 Or have I got it wrong, again? Link to comment Share on other sites More sharing options...
Pete Lewis Posted January 16, 2017 Report Share Posted January 16, 2017 the bush should have a spigot/shoulder that centralises the bush in the turret hole top and bottom are the same theres a simple cup washer sits either side of the bush and the shocker shaft has a register/stepped thread to control the amount of squash when you tighten the nut, the shocker shaft only has any load on it in the off the deck or off the car position and the spring length is restricted by the shocker being fully extened, on the road or with the suspension jacked there is no load and you can push pull the shaft quite easy, just some damped loading if the shoulder wont fit thro the turret theres a basic dimensional problem with the bushes just some ramblings Pete Link to comment Share on other sites More sharing options...
dougbgt6 Posted January 16, 2017 Report Share Posted January 16, 2017 The club shop ones do have a shoulder, as can be seen in the picture. Rimmers and Canleys ones don't, they are straight cut. Presumably relying on the dish in the top of the plate to centralise. Link to comment Share on other sites More sharing options...
Pete Lewis Posted January 16, 2017 Report Share Posted January 16, 2017 that rings a bell do some have cup washer each side of the flat bushes the washer having the location protrusion ?? cant remember something has to keep the shaft away/central in the turret hole or you get amazing squeaks you cant trace Pete Link to comment Share on other sites More sharing options...
Waynebaby Posted January 16, 2017 Report Share Posted January 16, 2017 Paul, Take a look at my post from the 25th October in the steering/suspension forum and see if that helps at all. I initially found that I couldn't get the top bushes through the hole too. Wayne Link to comment Share on other sites More sharing options...
68vitesse Posted January 16, 2017 Author Report Share Posted January 16, 2017 Thanks found your post same problem, have spoken to the supplier who stated that he has fitted them and the only way is on the car. Fit the lower top bush, cup washer and spring plate hold the spring in tension how ever you feel safe. Fit the unit to the car jack up under lower wishbone to compress the unit and fit top bush and cup washer. not in my opinion ideal working practice. Thank you all for your reply's. Regards Paul Link to comment Share on other sites More sharing options...
Waynebaby Posted January 16, 2017 Report Share Posted January 16, 2017 Paul, That sounds decidedly dangerous! I managed to fit the bush through the turret hole by making sure that the upper bush wasn't overly compressed under the top cup. Good luck! Wayne Link to comment Share on other sites More sharing options...
68vitesse Posted January 16, 2017 Author Report Share Posted January 16, 2017 Was thinking that I would assemble the unit with new polyurethane bottom bush and old rubber top bush fit to car and when back on its wheels change the top bush. Regards Paul Link to comment Share on other sites More sharing options...
Waynebaby Posted January 17, 2017 Report Share Posted January 17, 2017 That seems like a good plan. I found when refitting the unit that it was easiest to install the top end of the unit first and fully tighten the three retainer cap nuts, using a jack under the bottom of the shock to "help" it into position. This brings the bottom of the unit into the right orientation to lever into place in the lower wishbone. Regards Wayne Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now