daverclasper Posted May 30, 2019 Report Share Posted May 30, 2019 Hi. Does anyone know how many degrees, one of these (each side) will alter camber please?. Thanks, Dave Link to comment Share on other sites More sharing options...
Pete Lewis Posted May 30, 2019 Report Share Posted May 30, 2019 no mention of how much in my manuals one shim , wont make dramatic changes and camber is refered to as the sum of both sides div by 2 why do you need to change them ??? Link to comment Share on other sites More sharing options...
daverclasper Posted May 31, 2019 Author Report Share Posted May 31, 2019 Hi Pete. Nearside front tyre is wearing quite a bit more at outside edge. Have been swapping wheels around to even this out. Nowhere level at home, though have been doing a few randon, very basic checks, on car parks etc where car looks fairly level, using a piece of wood and spirit level across rim. Nearside appears it may have more positive camber, than offside, so wondered if to shim out 1 thickness (or more?) as have spare shims and see if it improves. Want to get new tyres soonish, so would like to sort if I can. I haven't checked tracking, though if this wear was too much "toe in", would it show wear on both outer edges?. cheers, Dave Link to comment Share on other sites More sharing options...
Pete Lewis Posted May 31, 2019 Report Share Posted May 31, 2019 no tracking problems wear the tyre on the easiest side to climb the road camber , to keep a straight lie the NS tries to climb the camber and the n/s outer gets worn . camber on its own wont wear tyres much but excess toe in will rip off rubber never to be replaced when its gone its gone use the two planks and a tape as per twiddle day , i think you just have excess toe in, forget camber remember on the roads the car doesnt know about camber and it splits the camber angle in half . camber can affect handling as the footprint is not equally placed on the rod there is no scrub taking place as the tyre rotates, where as tyres /\ or \/ scrub rubber as over the miles the sideways scrub is horrendous in comparision to any camber error pete Link to comment Share on other sites More sharing options...
Colin Lindsay Posted May 31, 2019 Report Share Posted May 31, 2019 Remember to shim both brackets on whichever side you're adjusting. Factory camber setting is +3.25 degrees, for all other Herald or all Vitesse models it's +3.5. (+5 on the rear) If your tyre wear is as bad as this one in the photo, it needs sorted. This was caused by slighty too much negative camber.... Link to comment Share on other sites More sharing options...
Gully Posted May 31, 2019 Report Share Posted May 31, 2019 Front of my GT6 used to run too much camber and over 13,000 miles in my ownership it did wear the fronts unevenly (by around 1.5mm comparing inside and outside of the tread). I replaced the tyres down to age, not tread depth. So it's a slow action. Compare that with the rear tyre that was running too much toe when I first had the car - it was at the tell-tale limits in under 4,000 miles from essentially new. There's a lot of advice across different online fora about whether the book camber values are still relevant to modern wider radial tyres on our cars. Many argue that zero camber or even slight negative camber is more appropriate. I reduced mine to around 1.0-1.5 degrees positive before putting the new front tyres on! I did remember to reset the toe! Gully Link to comment Share on other sites More sharing options...
Ben Caswell Posted May 31, 2019 Report Share Posted May 31, 2019 Don't keep using full lock to do U turns ! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now