Paul H

I see the above Webasto sold for £770 Paul

Not sure the cap is colour coordinated as you have the colour details overlaid . I’ve used the same spray can and the door was sprayed with celly from a 5 litre can from the club shop ( 4 coats ) Paul

Valencia Blue Code66 Paul

Do the rear overriders have an edging trim as they cover the bumper? Paul

Hi Colin I think you will find the wings are the new bit and the rest of the tub will need attention eg the wheel well is shot Paul

https://www.ebay.co.uk/itm/385332650165? Looking at the pics the rear window has a strut added , seller says the strut is attached . Any ideas ? Despite the rust the seller says it’s not been fitted before. I thought sunroofs were added by after market sellers Paul

Thanks and now understand . My clutch slave is leaking and considering moving across to Dot 5 . OKE dot 5 looks best value Paul

General DOT5 ? Autometic is much more expensive than say Comma DOT5 . Is it worth the premium Paul

This link might help I have fitted Freelander M12 wheel bolts to my Vitesse without the need of a Puller Paul

Apologies Johny “This overrider is suitable for the Triumph Herald range & Vitesse range. This item is brand new and is pressed off the OE press tool . It will fit on the left hand side of the car.” I’ll pamper them even more now Paul

Fitchets sold them as NOS and they will be pampered Paul

Hi Colin .Yes best to buy from their website , rather than EBay . Cheaper postage . Website says limited stock Paul

Should smarten up the rear of my Vitesse Paul

Thanks Gav , certainly worth a try as I do have a powerful magnet though the washer is stainless with some magnetism Paul

No luck with the magnet - too powerful . Camera didn’t show anything . Before I start pulling the box what could happen if I leave the washer in place Paul

Hi Pete , thanks for advice . The stainless washer has some magnetism after testing the other washer . I’ve taken a “super magnet” from my Milwaukee LED torch and glued it to the end of my magnetic wand and plan to test today . Now I know the camera picked up a clutch spring I will be exploring further to try and locate Paul

I think I’ve found the washer lodged in the clutch housing . Used my cheapie draper endoscope . Do you agree Paul

Thanks Pete . Will remove the washer one way or the other Paul

Hi Pete the other washer was stainless and not picked up by the magnet , I was removing the heater diverter. The annoying thing is I’ve done it before when changing the clutch slave and the magnet worked . Is it best to remove the box ?

Pretty sure I dropped a stainless washer in the clutch housing where the clutch release is . Is it safe to leave or do I have to get it out ? Paul

https://www.ebay.co.uk/itm/115657273343? one if the pics shows it in a GT6 Paul

Agree with Wagger . I’ve recently changed the sunroof top of my Vitesse Britax roof and wouldn’t be without it . The roof dimensions are likely to be the same . If you need advice / costings / suppliers let me know Paul

When I emptied the box of oil , there was no crud / debris ie no tell tale signs Paul

Yes leaving intact for when it’s required. I have another box , single rail spitfire box which is definitely for spares . The input shaft having significant rust . I purchased this one just for part 156911 as I understand this box shares the same 1/2nd synchro outer ring as the Vitesse . I’ll dig it out and start stripping just for the learning exercise Paul

Thanks Johny . I’ll use this box for spares when required . My current set up for my Mk 2 Vitesse is D type OD which Uncle Pete sorted for me a while back . On reassembly Pete noticed the 1/2nd synchro outer ring might be incorrect or out of spec as it had a lot of vertical / horizontal movement. Part no 156911 . At the time I couldn’t justify a new replacement £100 plus so the box went back as is . Currently 1500 miles plus and the GB is behaving and 2nd synchro ( changing down ) is sorted and no excessive noise. I bought this box for part 156911 should it be required also to learn how the GB works Thanks for all your input I’m a little wiser now . Hopefully others have gained some more knowledge . Paul