Ken Bradley Posted February 26, 2015 Report Share Posted February 26, 2015 Is the rear leaf spring "handed" on a 1500 Spitfire? In other words can I swing it round to overcome driver side sag, or is it to be a new spring. Link to comment Share on other sites More sharing options...
KevinR Posted February 26, 2015 Report Share Posted February 26, 2015 The spring is not handed, so it can be swapped around. Some original springs are marked to imply they are handed, but they are not. The problem is, that the sagging is probably not caused by the spring, it could be a problem with a stiff/seized trunion bush or other suspension component. Link to comment Share on other sites More sharing options...
ian.osprey Posted February 26, 2015 Report Share Posted February 26, 2015 ... also needn't be a problem at the front. Bent anti roll bars for instance Link to comment Share on other sites More sharing options...
Ken Bradley Posted February 27, 2015 Author Report Share Posted February 27, 2015 Thanks lads! I have been careful to assess the front and have indeed put a small spacer to lift drivers side slightly. However, there is still a sag which does appear to be "coming" from the back. Next step is to reverse that leaf spring! Link to comment Share on other sites More sharing options...
68vitesse Posted February 28, 2015 Report Share Posted February 28, 2015 When I first got my Mk1 Vitesse the car lent this was caused by the diff mounting. The diff rear bushes in a poor state and the mounting holes in the chassis worn. Bushes changed holes repaired with weld and reinforced with washers and the problem was solved. Regards Paul Link to comment Share on other sites More sharing options...
Ken Bradley Posted February 28, 2015 Author Report Share Posted February 28, 2015 Thanks for the input Paul, but this car is a bit different! I recently acquired the Spit and the previous owner has rebuilt the diff and fitted a lowering block. He has done some really good work on the car and I don't believe there is anything wrong with the diff mounting, but I admit I never noticed the lop-sided suspension until I was riding the car home! What I found interesting, and why I asked the original question, was on an American web site. Our American cousins apparently believe that Spitfires are very prone to driver side sag (maybe American drivers are heavier than we Brits). However, they seem convinced that the only real solution is to replace the leaf spring. It was that which I thought might be a bit drastic if you could try turning the thing round first! I'm going to give it a try. Link to comment Share on other sites More sharing options...
Alan C Posted March 8, 2015 Report Share Posted March 8, 2015 Driver's side sag at the rear is most likely caused by the rear leaf spring loosing it's strength. After all the driver's side is always "fully loaded" during every journey, unlike the passenger side. This was the case on my GT6 when I first bought it 28 years ago. Changing it for a new one cured the problem. The big advantage you have is that the Spitfire is not 'blessed' with the rotoflex suspension set-up as my GT6 was. So replacement is very straight forward by comparison, Swapping the spring around will only transfer the sag to the passenger side. This would however comfirm that the culprit is indeed the spring. Cheers Alan Link to comment Share on other sites More sharing options...
dougbgt6 Posted March 8, 2015 Report Share Posted March 8, 2015 My GT6 had sag on both sides when I first got it, turned out half the leaves were broken in the rear spring! Easy to change though, no rotoflex! Link to comment Share on other sites More sharing options...
Pete Lewis Posted March 8, 2015 Report Share Posted March 8, 2015 as the lean is on a 1500 i guess this has a swinger in which case the lean is less likely to be spring dependant as there is only one leaf clamped to the diff. the remain float in the pivot box.and will tend towards a self centre . jack the car in the middle at the front measure the w arch to deck then same at the back , this will show which end has the lean. I would agree its more likely anti roll or stiff trunion to check the arb you only need to discon one end if its bent it will ping out of alignment . Pete Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now