Waynebaby Posted February 18, 2019 Report Share Posted February 18, 2019 Hi All, I've finally got around to buying a hinge pin to replace the worn item in the top hinge of my drivers door. I'm wondering what is the best way to approach the task of replacing it. I'm pretty sure the door will need to come off, but don't know if the pin can be driven out with the hinge still attached to the A-post or if it is easier to take the hinge off completely and try pressing it out off the car. Also I don't know if the pin has to go in (and therefore come out) in a particular direction. The pin has a splined end, but I'm not sure what that is for. Any suggestions grateful received. Thanks Wayne Link to comment Share on other sites More sharing options...
Colin Lindsay Posted February 18, 2019 Report Share Posted February 18, 2019 Take the hinge off completely; it'll be much easier. I'm assuming - (I have four of these for the Herald, not yet used!) that they drop in from the top and can only go so far into the hinge before the splined end bites and holds it in place, so have to be pushed upwards to take them out. Refitting is a case of pressing them in from the top until they're flush. I'll maybe go practice on an old hinge and report back later. Link to comment Share on other sites More sharing options...
AidanT Posted February 18, 2019 Report Share Posted February 18, 2019 It's a fun job and agree with Colin. I did the same bug found it was the hinge that was worn and not the pin! Aidan Link to comment Share on other sites More sharing options...
Pete Lewis Posted February 18, 2019 Report Share Posted February 18, 2019 Yes take hinge off the car , You should be able to see the end of the spline so drive it out from the opposite end They do remove with a vice or hammer but if seized in can be troublesome You can drill out and fit oversize pins or bolts New are available Pete 1 Link to comment Share on other sites More sharing options...
Waynebaby Posted February 18, 2019 Author Report Share Posted February 18, 2019 Thanks guys. I noticed that it is possible to buy complete new hinges after I bought the pin (typically) but now I have it I may as well use it. Link to comment Share on other sites More sharing options...
GFL Posted February 19, 2019 Report Share Posted February 19, 2019 I'm just in the Process of changing these Hinge pins on My Sunbeam? I managed to press two of them out using the vice with a suitably sized short bolt and spacer at the other end. One was a bit harder and needed drifting out and the 4th one wouldn't budge at all, even with the use of heat and a large hammer and drift it wouldn't budge, turns out it had snapped. I ended up having to cut through the pin with a junior hacksaw, but the Sunbeam hinges are different to triumph ones with brass spacer washers in between each section which give just enough room for a junior hacksaw. I've got the problem now of the pins having worn the hinge holes oval, so I need to have them drilled/machined to suit larger diameter pins?!!! Unfortunately new hinges are not available for the Sunbeam Alpine/Tiger range😞 1 Link to comment Share on other sites More sharing options...
Colin Lindsay Posted February 19, 2019 Report Share Posted February 19, 2019 38 minutes ago, Gary Flinn said: That's made me feel so much better, that I'm not the only one who ends up with pics like that! If I'm doing that sort of thing I need about four hands to hold a big socket, a small socket, a drift, and turn the vice handle at the same time... Were those hinges used on any other model? Link to comment Share on other sites More sharing options...
GFL Posted February 19, 2019 Report Share Posted February 19, 2019 2 minutes ago, Colin Lindsay said: That's made me feel so much better, that I'm not the only one who ends up with pics like that! If I'm doing that sort of thing I need about four hands to hold a big socket, a small socket, a drift, and turn the vice handle at the same time... Were those hinges used on any other model? Colin I've no idea, still finding my feet with the Rootes group cars? Gary Link to comment Share on other sites More sharing options...
Colin Lindsay Posted February 19, 2019 Report Share Posted February 19, 2019 https://www.sunbeamclub.com/forum/tiger-club-forum.4/help-trying-to-locate-door-hinges-for-1966.68403/ Apparrently some owners have found that the solution is to rebush the hinges, then use a new pin. Sounds like a plan. 1 Link to comment Share on other sites More sharing options...
GFL Posted February 19, 2019 Report Share Posted February 19, 2019 Colin That may be the way to go for me? I wonder if I can source some in the UK? Gary Link to comment Share on other sites More sharing options...
Colin Lindsay Posted February 19, 2019 Report Share Posted February 19, 2019 https://www.amazon.com/Oilite-AA306-10B-Genuine-Sintered-Bearing/dp/B0787GLGY9 Amazon have no more listed for sale in the UK but these guys in the USA will ship internationally. Part number is AA306 - 10B, by Oilite. 1 Link to comment Share on other sites More sharing options...
PeteH Posted April 3, 2019 Report Share Posted April 3, 2019 If you have access to a lathe, they should not be that difficult to drill out oversize and turn bushes?. I find odd ends of brass etc on tool stalls at shows etc, Pete. Link to comment Share on other sites More sharing options...
rogerguzzi Posted April 3, 2019 Report Share Posted April 3, 2019 2 hours ago, PeteH said: If you have access to a lathe, they should not be that difficult to drill out oversize and turn bushes?. I find odd ends of brass etc on tool stalls at shows etc, Pete. Hello All If you have a lathe (or a friend with one) I drilled the hinges o/s and made pins to suit Roger Link to comment Share on other sites More sharing options...
PeteH Posted April 3, 2019 Report Share Posted April 3, 2019 43 minutes ago, rogerguzzi said: Hello All If you have a lathe (or a friend with one) I drilled the hinges o/s and made pins to suit Roger Yes another option, It`s just me, I like to see "bushed" hinges, it`s quite satisfying to produce a bearing in Non ferrous material, rather than the relativity crude, but obviously cost "effective" in O/E manufacturing steel on steel. Pete Link to comment Share on other sites More sharing options...
rogerguzzi Posted April 3, 2019 Report Share Posted April 3, 2019 1 hour ago, PeteH said: Yes another option, It`s just me, I like to see "bushed" hinges, it`s quite satisfying to produce a bearing in Non ferrous material, rather than the relativity crude, but obviously cost "effective" in O/E manufacturing steel on steel. Pete Ha Ha Pete are you expecting to be here in 30 years time? Roger Link to comment Share on other sites More sharing options...
PeteH Posted April 4, 2019 Report Share Posted April 4, 2019 12 hours ago, rogerguzzi said: Ha Ha Pete are you expecting to be here in 30 years time? Roger No, Mind I`ll only be 105, But I hope the car is?. My Grandson, is already coveting it, he has actually done a little bit of the welding and is learning to fabricate panels, it is still a work in in progress but he comes and does a bit when he is on leave. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now