Colin Posted July 30, 2019 Report Share Posted July 30, 2019 Folks:- I have been titivating my 1970 Herald 1200 Saloon over the last few months to make her look more respectable and eventually coax her out on the road again. I think I can black window seal repair my front screen rubber - but the rear is pretty well u/s. If I buy a replacement seal (apparently the quality of these new items is questionable??) and I have looked at copious YouTube examples of a single person doing same, but as I've not done this before, what chance does anyone think I have of re-installing the glass with new seal on my own ??!!?? All thoughts welcome . . . Link to comment Share on other sites More sharing options...
poppyman Posted July 30, 2019 Report Share Posted July 30, 2019 Hi Colin, dont bother....... get the proffesionals in. They will do it in a fraction of the time and it's not expensive. Tony. PS, welcome to the forum. Link to comment Share on other sites More sharing options...
Pete Lewis Posted July 30, 2019 Report Share Posted July 30, 2019 you really need someone on the outside to apply pressure while you string it in place, you can lean the spare wheel against the screen to hold it best stuff for sealer is simple gutter black sealer , goes on easy cleans with white spirit , ( warm cartridge to ease flow ) two ways apply sealer glass to rubber and around the seal rubber to aperture then pull it in or assemble dry and insert sealer nozzle in the seal after stringing old trick is fill old leather glove with shot or sand to use as a whacker to bed the glass and seal into the aperture being toughen glass you can be quite rough it wont break , much more care if laminated ( all glass is marked so you can tell what youve got dont use any silly prices silicon type stuff , you are sealing the glass /rubber not adhering it in place . ( i was instigator of dry seal rubbers back in the 80s ) pete Link to comment Share on other sites More sharing options...
Colin Lindsay Posted July 30, 2019 Report Share Posted July 30, 2019 1 hour ago, Pete Lewis said: you really need someone on the outside to apply pressure while you string it in place Yep, that's the best way - a person can shift about as required whereas a dead weight can't. They don't need any kind of mechanical expertise, they just have to press as required... Link to comment Share on other sites More sharing options...
Colin Posted July 31, 2019 Author Report Share Posted July 31, 2019 Gents:- all the above opinions are what I needed to know - thanks very much. Always like to try jobs myself if I think they're achievable. Have done most mechanicals and a lot of filler & paint repair jobs myself (shooosh!!) in the past, but as you rightly say, without a second pair of hands, probably best to call in 'the firm' . . . :-) Once again, thanks. Link to comment Share on other sites More sharing options...
Dave the tram Posted July 31, 2019 Report Share Posted July 31, 2019 Does anyone know typical cost to get professionals in to fit a screen, and any to recommend? I've just got a new laminated screen and rubber seal from Rimmers waiting to go in and keep dithering about doing it myself with a helper and soapy string. Also, if it goes in ok using string, does it actually need any sealant unless I discover leaks? Cheers Dave Link to comment Share on other sites More sharing options...
Pete Lewis Posted July 31, 2019 Report Share Posted July 31, 2019 Yes it will need sealing, it may be ok but the old design is expecting sealant Especially in the corners as the new seals probably are not formed at the corners and the flips will collapse . Take care with laminated easy to crack if you get excited with it. Use woven cord to string it in , overlap along the bottom so you can work left and to the right Some soft soap on the apperture to aid the flip rolling over the flange See my tip about sand filled glove to use as a soft pat it in device Pete Link to comment Share on other sites More sharing options...
poppyman Posted July 31, 2019 Report Share Posted July 31, 2019 Try to avoid the big boys Dave and go for one of the small firms. If you can take it to them? It will be cheaper. The last one i had fitted was about 5yrs ago and was £40. Tony. Link to comment Share on other sites More sharing options...
Dave the tram Posted August 2, 2019 Report Share Posted August 2, 2019 Pete, using sealant as you fit it sounds like it could get messy, especially if I'm learning as a go along. Does it work ok to inject sealant once the screen is in? If so, do I just seal from the outside between screen and rubber, then between body and rubber? I've fitted the rubber onto the new screen already, and yes, one corner has a slight gap where the rubber creases out slightly. No rush to fit it and will wait until I've decided on best method. Cheers Dave Link to comment Share on other sites More sharing options...
Colin Lindsay Posted August 2, 2019 Report Share Posted August 2, 2019 Let it settle for a bit, if possible park facing the sun to soften the rubber and let things attain a proper profile against the screen frame; after a time there will be fewer gaps and sealant will be more effective. If you apply sealant now, when the rubber is still conforming to the shape of the frame, it will harden and hold the rubber away slightly, perhaps leading to leaks later on. Link to comment Share on other sites More sharing options...
Pete Lewis Posted August 2, 2019 Report Share Posted August 2, 2019 you can pipe the sealer in after fitting if you want , i would suggest adding a short bit of smooth flatted metal tube and fix it to the cartridge to make it easier to slide around under the rubber. the black gutter type sealer is best , yes it can be messy but white spirit and scraper soon clean it back to a neat finish if the corners are folded in or are shy to the aperture corners you can slice a short lenght of screnwash tube and insert in the edge of the glass to push the rubber outwards if you seal the rubber before fitting sticky tape the end of the strings to the middle of the glass to keep it out the way Pete Link to comment Share on other sites More sharing options...
daverclasper Posted August 2, 2019 Report Share Posted August 2, 2019 (edited) 2 hours ago, Colin Lindsay said: Let it settle for a bit, if possible park facing the sun to soften the rubber and let things attain a proper profile against the screen frame Don't leave too long in the sun, if a repro seal. It be knacked. Only half joking. Dave Edited August 2, 2019 by daverclasper Link to comment Share on other sites More sharing options...
Dave the tram Posted August 2, 2019 Report Share Posted August 2, 2019 Thanks all, will try the trick of packing the one slack corner with a bit of tube, then get it warm for a bit to mould to shape, then use gutter sealant with an appropriate nozel. Fingers crossed. Dave Link to comment Share on other sites More sharing options...
Pete Lewis Posted August 3, 2019 Report Share Posted August 3, 2019 just drop the thing into the bottom flange , or you will get it on the surround ...more cleaning slice a tube in half , a full section will be too big Pete Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now