Richeee Posted January 21, 2023 Author Report Share Posted January 21, 2023 Right, here we go again. Not so much work this week as had to accept some paid employment for a few weeks. Im not old enough to retire but dont work as much as i should. But it was offered and a few bills to pay. Today however managed to grab a few hours. First thing first of course was load up the garage pie warmer. Then could commence. 2nd job was to remove the seat belt backing nut and plate from the old inner wing. Measure and mark on the new wing and remp hold in place with nut and bolt and weld it in position. The main object of the day was to coat the base of the tub in Rustbuster Epoxy primer / finish 121. So final holes were welded and grinding was undertaken. Tub turned upside down and painted with a brush and roller. This 121 can be a finish coat or a primer. Im using as a base, rust prevention layer whilst i do other jobs. Later on in the build it will be rubbed down, joints seam sealed. Then recoated in 121 befor recieving the body colour. It went on diffetent than i expected. Certainly thicker than i expected and they say dont over thin. It can be used with just an ordinary full face mask. Had 2 3kw fan heaters working away and now have left an oil readiater on to keep frost away. Will see what its like when it dries. Next job will be to swap the tub over and coat the rest of the tub in their 421 epoxy primer. With work commitments that may well not be for another week or so. To be continued. 2 Link to comment Share on other sites More sharing options...
Richeee Posted February 22, 2023 Author Report Share Posted February 22, 2023 Well a month later am i able to get back in the garage. Work got in the way , this freelance stint now over ,and my son who has been living with me since he was pushed of the road by an hgv and broke his arm and leg, has required attention. Just that hes repairing well and we live in the middle of nowhere so come weekends We have been out and about trying to stop him going stir crazy 🤪. Hes now returned to his digs in Reading and is on a phased return to teaching so normal service is now resumed. Left it with the bottom of the rear tub being epoxied mastic. This is it 1 month later. Time to flip the tub upright and rub down the rest for the mastic 121 from rustbuster. But then remembered holes i knew about but had been putting off doing. These are to the rear deck where the hood would sit harbouring damp. Bit of a go with the welder and ground a bit with the finger file. Then i was inspecting under side of the wing tops by the b posts and decided i needed ro rub down and apply more rust convertor before apply the epoxy. So a few hoursdoing things I was not expecting to do. But is that not the way of it sometimes. To be continued. 1 Link to comment Share on other sites More sharing options...
Richeee Posted February 26, 2023 Author Report Share Posted February 26, 2023 Yesterday was either cutting hedges in north esterly wind or working in the garage. Decided the garage. Spent the day coating the tub in epoxy mastic over the red novol primer. Rubbed it down first. It was applied by a mixture of brushing, rolling and spraying. Some areas difficult to get into especially the depths of the B posts. These will recieve treatment anyway later. The tub will be stored back in its rightful place on the chassis whilst the the bulkhead recieves the same treatment. The finish is not perfect but the idea is to give it some better protection than the primer it already has whilst other work carries on. Link to comment Share on other sites More sharing options...
Richeee Posted February 26, 2023 Author Report Share Posted February 26, 2023 Lazy morning then decided to progress a bit more. If progression today was the right term. Was able to manhandle the rear tub onto the chassis and tempoarily basked in what it might be in a couple of years time. But time to move on. The bulkhead was removed and placed on a trestle table. I thought for two minor 1 second welds and then a rub down and prime. But unfortunately like a scab i picked at the spots. Nothing for it. The gutters to the windscreen needed to come off. The gap between the pillar and the gutter trim was powdery rust. Oh well , rub it down and see whats left. It was left with a coating of rust convertor and a note to order 2 new gutters. To be continued. Link to comment Share on other sites More sharing options...
Richeee Posted February 28, 2023 Author Report Share Posted February 28, 2023 Bitterly cold wind again today, so hedge cutting could wait again. Oh dear, never mind , how sad, get to spend few more hours in the garage with 2 heaters running. No point having a hobby if you dont enjoy it in the warm. We have some brilliant suppliers. Ordered 2 gutters sunday afternoon from John Paddock. Lunchtime today they are on my doorstep. Fantastic. Continued with left hand windscreen pillar , repairing and letting bits of steel. More patching and welding and could try gutter for fit. The bottom return drip leg being a bit of a fiddle but eventually a decent fit. It was punched for plug welds and then both surfaces coated with weld through primer. Next to rove the rh gutter whilst the primer was drying. Good job i decided to do both gutters. Certain that the baking and stripping process caused some of this as the old trapped paint from 60 years ago turns to powder. But the greater amount is just pure old fashioned rust. This was cleaned , welded , the gutter trial fitted and rust converted. Now back to the lhs , the now dry gutter was welded in place. Again fiddly on the drip piece, but all worked out in the end. To be honest am quite pleased with todays efforts. To be continued. Link to comment Share on other sites More sharing options...
Josef Posted February 28, 2023 Report Share Posted February 28, 2023 Now what are the through hole clamps you’re using there called? I’ve heard them named in a bunch of different accents on YouTube but can’t get a close enough spelling to search for them! Link to comment Share on other sites More sharing options...
Richeee Posted February 28, 2023 Author Report Share Posted February 28, 2023 Cleco pins. Took myself a bit of searching first time. Excellent for trial fitting of panels. Link to comment Share on other sites More sharing options...
Josef Posted February 28, 2023 Report Share Posted February 28, 2023 Thanks. I was using too many k’s and too many e’s! Link to comment Share on other sites More sharing options...
PeteH Posted March 1, 2023 Report Share Posted March 1, 2023 10 hours ago, Richeee said: Cleco pins. 👍, For years I had a box full. Curtesy of a one time employer who went bust!. Then it went missing😭. Main suspect, as Usual, youngest son? denies it of course.!! Gone now as he`s no room for storing that stuff on a Barge. But He still has the Router!!. Pete Link to comment Share on other sites More sharing options...
Peter Truman Posted March 1, 2023 Report Share Posted March 1, 2023 I had a club contact who went back to England and was living on a barge his comment was damned cold in winter Link to comment Share on other sites More sharing options...
Pete Lewis Posted March 1, 2023 Report Share Posted March 1, 2023 these are what you are looking for Link to comment Share on other sites More sharing options...
PeteH Posted March 1, 2023 Report Share Posted March 1, 2023 10 hours ago, Peter Truman said: I had a club contact who went back to England and was living on a barge his comment was damned cold in winter Yes, With the best will in the world the steel structure sat in cold water, is never going to be easy to Insulate, The Son has a Big Multifuel stove in the main cabin, but the Webasto Oil Fired Heater stuggles to heat the rest of the Boat. Worse was last summer when we had 40C+ weather and the Cabin became virtually untenable at times. Pete Link to comment Share on other sites More sharing options...
Richeee Posted March 2, 2023 Author Report Share Posted March 2, 2023 To be honest the sun was shining birds a twittering and I should really have done some hedge cutting, but really wanted to work in garage. So i did. You can see i live alone. Nobody putting jobs in my way. First off fit the other windscreen gutter. All ok. Not to many problems. Went better when i remembered to turn the gas on the mig....... Also to repair a small hole where the heater blower sits. Turn your back and you see another one. That should be the bulkhead ready to go. So wire cup in a grinder and prepared the underside. You can clearly see here the work i had to do previously to reduce the footwells , to relocate the chassis rails for the borg warner auto box. The actual tunnel width is the same as the flats pass over the new rails. But the actual recesses are narrower. Good job theres only 2 pedals. The day was finished with some Rustbuster 121 epoxy mastic primer / chassis protector being brushed applied. Again this will have a second coat after the car has been dry assembled. Then stripped again, and will also recieve body colour. To be continued. 3 Link to comment Share on other sites More sharing options...
Richeee Posted March 20, 2023 Author Report Share Posted March 20, 2023 Hi. My last post was nearly 3 weeks ago. Spring holiday to Malta got in the way. 20.c sunny weather, plenty of eateries just outside my hotel, and as it was a solo's organised tour holiday plenty of trips out. Any way back to blighty. My freelance work was cancelled and as too wet today to cut hedges again. (Always an excuse not to cut hedges ) it was back working on the bulkhead. Left with have just used rustbuster epoxy mastic on the base. It was now time to rub down the rest of the bulkhead to recieve its first coat. Also used a flexi drain cleaning rod in my drill to clean out inside the a post and bulkhead frames. Was going to spray in rust convertor. But my flexi hose and my schultz gun were not compatible with my container. Have now ordered new to rectify. Rubbed down the novol primer. Then brushed on the epoxy primer. Thats now the tub done and the bulkhead. When my proper schultz tin turns up i will spray rust convertor in the a post and windscreen frame. But next major job now is the bonnet. To be continued. 1 Link to comment Share on other sites More sharing options...
Richeee Posted March 22, 2023 Author Report Share Posted March 22, 2023 Only 5 mins work lifting bulkhead off trestles and putting on chassis with the tub. And i know it will be coming off again several times but gave myself quite a boost to think i am getting there slowly 4 Link to comment Share on other sites More sharing options...
Richeee Posted March 22, 2023 Author Report Share Posted March 22, 2023 (edited) Bonnet ... After the morale booster of putting the on the bulkhead chassis it was time to address the bonnet. The bonnet had been sent up to stripped and dipped along with the other body sections 9 months ago. So overall does not look to bad in shiny primer. However the only panels were saving are the bonnet top. The front panel and the two inner arches. The two wings are badly holed , distorted and dented. Even though they dont look to bad from across the street or on photos theyare not worth saving. Now some of you may differ on that point. Fortunately in my travels had picked up 2 wings. These had been around a bit, but straight apart from a couple of pea sized dents. They were older in black primer. These had been stripped as well. The inner arches were no longer and replavements have been ordered. Unfortunately i had over looked sending the inner arches to be stripped. They were in the boot of my parts car. They needed seperating from the remains of the outer arches and some holes patched where the bonnet tube holds mud and the leading edge of the rhs was a bit ragged. But repairable. Hiding away in my parts car. Looks lot worse in real life. Not easy to tell but dented and distorted. New wings and corner brackets. Holes on inner arches covered by tube. So settled down with The Hunt for Red October and started patching the inner arches. Slight health and safety issue when i set light to myself. Best find my leather apron. Getting there on rhs inner arch. And left them covered in screwfix paint stripper. To be continued. Edited March 22, 2023 by Richeee 1 Link to comment Share on other sites More sharing options...
Pete Lewis Posted March 23, 2023 Report Share Posted March 23, 2023 its all going to make you smile when its finished , stray sparks and clothing are not a good mix pleased you escaped ok Pete Link to comment Share on other sites More sharing options...
Colin Lindsay Posted March 23, 2023 Report Share Posted March 23, 2023 Superb work. Am well impressed! Link to comment Share on other sites More sharing options...
Richeee Posted March 23, 2023 Author Report Share Posted March 23, 2023 (edited) Thank you but perhaps a bit hasty. Was working on the inner arches again today, and where i had been grinding the welds down held a light behind them and it was like a lace curtain. Welded some more and ground some more, burnt through, chasing holes, grrrrrr, then gave up and put them (threw) back in storage. Jurys out on them at present. It was at this point i put Zulu on the telly and pondered what to do next whilst i calmed down from my hissy fit. At this point heard a van on the drive. The outer arches had arrived. Ordered yesterday morning from James Paddock. Excellent service. That was just standard delivery. so went ahead and trial fiited them to my new wings. How on earth your supposed to paint or protect the non accesible void between them is a question being posed on another thread. All i can quess is some very runny paint dribbled and allowed to flow in followed by some wax protection. Anyway with a bit of jiggling both were trial fitted. Eaisier to trial fit now when there is full access all round. The return flages on both needed a bit of fettling but the fit was pretty good straight out the box. Now disassembled to be installed after the wings are fitted on. Now time to attack the old wings and remove from bonnet. Marked where to cut & span the cutting disc up. Then started to remove the spot welds to remove old flanges. Noticed a problem with the wings however. Around the headlight ring is a foward flacing flange which then returns backwards as it meets the grill panel by the side lights. However when i compare to the new wing the flange continues to point forward. Not insurmountable, just a pain. And as for the hedge cutting. Decided to 'get a man who can' to cut them for me. So more garage time. Although i do have some paid work coming up next week that will restrict my efforts. To be continued. Edited March 23, 2023 by Richeee Link to comment Share on other sites More sharing options...
Pete Lewis Posted March 24, 2023 Report Share Posted March 24, 2023 magic work it will soon be good as NEW ...Hmmmmm more Tea and Biscuits should work well Pete Link to comment Share on other sites More sharing options...
Richeee Posted March 24, 2023 Author Report Share Posted March 24, 2023 (edited) Unfortunately quite a bit will be new. Panels ,interior, mechanics. When you start with a basket case that i suppose is what you get. I realise i could have purchased a running herald for about a 3rd its going to cost me , and i will lose money, but thats not what i do it for. This is my 5th Triumph over many years. Started with a Tr7 when i graduated as an engineer in the early 80,s. 3 months later i had to sell it as repair bills were crippling me. Along came a Ford Capri only 2 years old and ran perfectly. Had a Volvo 122s, another Tr7, this time i could afford to have it as a toy. Still had to do a lot of maintenance to keep it going. A herald saloon , and 10 years ago acquired this basket case off my brother. He had it 10 years before me and it was a basket case all the time he had it as well. So its time had come, for some TLC. My dearly beloved passed 7 years ago and i purchased a series 2a land rover to restore in my happy place. The garage. This was completed after 3 years. Drove for a month and then sold. Mainly because i was too big to drive it with out my knees giving out. 6ft 3 and 19 stone. Kids have left home although they come back regularly to keep an eye on me. Semi retired and i can do a bit what i like. Although I still do freelance work to pay the bills, And some of my clients call me in to help out in holiday times etc. The herald is a bit like climbing a mountain. Why. Because its there. I will try and repair where i can but what i cant will be replaced. The alteration of the chassis for instance to fit an auto box. I like automatics. So relaxed driving. And with this herald being a keeper its got to be how i want it. And I was told it could not be done. Red rag and bull came to mind. I have since learnt there may be 3 others. Tom L having a vitesse I understand. Must get up to see it So today it was one of my 3kw heaters in the garage running and as the new John Wick film is released to day, watched John Wick 3, in the garage followed by Jaws, and then Clint Eastwood in Cry Macho. An update of todays progress will follow later. To be continued. Edited March 24, 2023 by Richeee 2 Link to comment Share on other sites More sharing options...
Richeee Posted March 24, 2023 Author Report Share Posted March 24, 2023 (edited) Work continued on the bonnet today. Removing the old wings, and brackets that the cones locate into. Spot welds were drilled out, and with an cut off saw , finger file, and an old screw driver as a chisel, carried on. Before I cut the other wing off, i was still perturbed by the flange around the sidelight pointing forward instead of backwards. As i offered up the wing in order for the semi circle to fit snugly around the headlight ring , it was obvious the actual wing was a bit long before it hit the grill panel as well. Oh well, will have to be reshaped. Maybe i have a cunning plan. Couple of rust spots on the little brackets that give a support to the front grill panel was poked out. Will be welded later, but was treated in convertor. Finished off with both wings removed, the flanges prepped and coated in primer. Next job will be starting to fix the new wings. Not sure when i can get back to it, as have some work for at least a couple of weeks to pay some bills. But as normal, To be continued. Edited March 24, 2023 by Richeee Link to comment Share on other sites More sharing options...
Richeee Posted April 1, 2023 Author Report Share Posted April 1, 2023 Back again. Perfect garage weather. Chucking it down. Garden squelchy, and no guilt about not cutting the church grass. Another job i seem to have inherited from honouring my mother. The old boy who normally does it is 80. And wondered if i could. I could not say no. So pie in the heater tray. Michael cain as Harry Palmer on the telly and set to work. Trial fitting the wing. The wing came with a extension piece that fixs to the bonnet top bulkhead end. This was getting in the way. So at first cut it to bend it. Eventually cutting it off completely. It will go back on later . When welding the wing on finally and the cone locating bracket. Trial fitted again to see how it fitted at the front. Using the rear of the bonnet as the flush ref point. As mentioned befor the wing flange to the grill panel pokes forward not rearwards and also the wing overlaps the grill panel. Also the brazed connection to the bonnet top and wing was preventing the wing sitting snugly. So a little metal was removed with the 75mm cut off disc. They are great for small cutting and grinding jobs. (Though not really suposed to grind on the edge) Memory getting bad and had to keep checking the layout on my parts car. With the wing to bonnet top cleco'd along the edge it was time for the front. Marked up what had to be cut off and cut it. Leaving me with this connection between the grill and the wing. Bent the flange rearwards, in.the end most successful with pliars. Not really the best but in such an awkward spot. The grill panel was actually a couple of mm higher than the wing. I know in its correct orientation other way up it might not ever be spotted. Made a thin cut in the grill.panel and gently tapped down. Looking ok. Quite pleased how that turned out. Next onto D plate supporting wing and grill. Without to much fuss. This is an oldpanel that came with the car from my brother , many moons ago. Now confession time. The inner arch's i was repairing and then threw in the corner on my junk pile. Stayed there and 2 more were procurred via the club and came very quickly. And proved to be a very good fit. Right fecision for me, but maybe not for everyone. Next the outer arch i had trialed fixed to the wing was re pinned to see how it coordinated with the D plate etc. Bit of bending to front flange required. Then taken off again and the new inner flange trial fitted to the outer. After which it was all pinned in place. Finishing off with the bracket for cone location. This was initially to wide to fit in the new wing return flange. But a bit of cutting and it will slide into place. After that massive jigsaw puzzle it was all taken apart and cut edges etc painted in weld through primer. When i can next find some time i will break open the welder. Punch some holes for spots and see if i can set light to my self again. To be continued. 2 Link to comment Share on other sites More sharing options...
Richeee Posted June 17, 2023 Author Report Share Posted June 17, 2023 Not to worry. Normal service will be resumed on my restoration. A. I was getting a bit demoralised that i did not have a Triumph to drive and my mgf had to go but needed its head gasket doing as per other thread. Then decided to put up a car port to offer protection to my new spit. Bit of tinkering on my spit. B. Garage and house now full of furniture from the daughters and sons flats moves not alligning correctly C. Nearly completeing the sell of my late sisters house. Clearing that out and admin of 15 beneficiaries along with administration of late mothers field sales has got a bit in the way. Dont mention the sciatica or paid work that im not doing enough off. But the end is in site and after a series of car boot sales, sisters house completing in a couple of weeks ,Daughter about to move into new house I can get my garage and mojo back. Almost long for the wet dark days of winter where i can shut myself away in the garage. It will definetly be continued. But first got to get up and clean my sisters house. Or rather supervise family members cleaning. Their has to be some effort involved in beinf a beneficiary. To be Continued. 1 Link to comment Share on other sites More sharing options...
Richeee Posted July 5, 2023 Author Report Share Posted July 5, 2023 Thought my storage problems wew improving and for a period of 8 hours had an empty garage last weekend. My daughter and partner who waS staying with myself whilst their house purchase was completed moved in last friday. Unfortunately that evening they put the dushwasher on to clean it out. The house was empty for a year. It promptly caught fire. 2 engines out and co2 water used. That evening back with me at 2 in morning. Fortunately restricted to kitchen but smell lingers. The brigade were quick. They live on the hampshire wiltshire border and its a race between Fordingbridge and Salisbury crews as to who can get their first. So garage now used as storage again. Electricians and gas engineers been out. Cleaning crew due tomorrow and they intend to try moving in again. See what happens and if i get my garage back. To be continued. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now