Robin Posted September 4, 2016 Report Share Posted September 4, 2016 Hi All I need to replace the green/red stripe left hand rear indicator cable in the wiring loom - does anyone know a supplier where I can buy a couple of meters? Thanks Robin Link to comment Share on other sites More sharing options...
Darren Groves Posted September 4, 2016 Report Share Posted September 4, 2016 Www.autosparks.co.uk Link to comment Share on other sites More sharing options...
Guest Posted September 4, 2016 Report Share Posted September 4, 2016 Hello Robin. I use ALM Solutions: ALM Electrical SolutionsBroad Ground RoadLakesideRedditchWorcestershireB98 8YP Office hours are 8.30AM - 5.30PM Monday to Friday Telephone: 01527 521600 www.almsolutions.co.uk They are spot-on with service and products, plus list every wire colour combination you could wish for. In addition they do a lot of thin wall wire which is the way forward these days in so much that the wire is thinner and yet can carry a high amp rating. They advertise a lot on Ebay and here's a link to get you on their selling site: http://stores.ebay.co.uk/almelectricalsolutions/ Good luck. Richard. Link to comment Share on other sites More sharing options...
Robin Posted September 5, 2016 Author Report Share Posted September 5, 2016 Thanks both - what amp rating should I look for and are bullet connectors ok or would spades be better? Link to comment Share on other sites More sharing options...
Guest Posted September 5, 2016 Report Share Posted September 5, 2016 Robin. Thin wall wire carries a high amperage so for example 1.0mm2 cross section is capable of up to 16.5amps. However in your case 0.5mm2 is fine as it can handle up to 11amps - more than sufficient for your rear lamps. I have searched and included a link from ALM via Ebay for your assistance: http://www.ebay.co.uk/itm/0-5mm-12V-24V-Automotive-Marine-Auto-Cable-11Amp-Thinwall-All-Colours-Lengths-/321323682498?var=510232441704&hash=item4ad0624ac2:m:mPXgugvE_7fCfAE5jhpE1nA Personally I prefer the old style bullet and black rubber insulators. The bullets can be soldered once the wire is inserted, if required, and these items keep the era of the car correct. Again here is a useful link showing the items as an example only, there are plenty of sellers on Ebay - just ensure you get the brass bullets: http://www.ebay.co.uk/itm/4-7mm-Lucas-style-Brass-Bullet-Male-Connectors-Sockets-Female-Pk-of-35-/301390875277?hash=item462c4bca8d:g:~nQAAOSwuMFUY21l I tend to buy packs of bullets, single & double connectors via Ebay, not had a problem yet. That has done it !!!!!!! Hope the above assists ?? Regards. Richard. Link to comment Share on other sites More sharing options...
Robin Posted September 5, 2016 Author Report Share Posted September 5, 2016 Robin. Thin wall wire carries a high amperage so for example 1.0mm2 cross section is capable of up to 16.5amps. However in your case 0.5mm2 is fine as it can handle up to 11amps - more than sufficient for your rear lamps. I have searched and included a link from ALM via Ebay for your assistance: http://www.ebay.co.uk/itm/0-5mm-12V-24V-Automotive-Marine-Auto-Cable-11Amp-Thinwall-All-Colours-Lengths-/321323682498?var=510232441704&hash=item4ad0624ac2:m:mPXgugvE_7fCfAE5jhpE1nA Personally I prefer the old style bullet and black rubber insulators. The bullets can be soldered once the wire is inserted, if required, and these items keep the era of the car correct. Again here is a useful link showing the items as an example only, there are plenty of sellers on Ebay - just ensure you get the brass bullets: http://www.ebay.co.uk/itm/4-7mm-Lucas-style-Brass-Bullet-Male-Connectors-Sockets-Female-Pk-of-35-/301390875277?hash=item462c4bca8d:g:~nQAAOSwuMFUY21l I tend to buy packs of bullets, single & double connectors via Ebay, not had a problem yet. That has done it !!!!!!! Hope the above assists ?? Regards. Richard. Hi Richard - thanks for the info. Out of interest do you know what the indicator lamps draw in terms of amps? Link to comment Share on other sites More sharing options...
Guest Posted September 5, 2016 Report Share Posted September 5, 2016 Robin. Use this formula for watts, volts and amps. So in your case the amp requirement is: Watts (W) divided by volts (V) = amps (A) With this equation you can swap the A, V and W about to determine the answers for each constant. Off the top of my head I'm 99% certain indicator bulbs run with 21W; so less than 2amps per bulb using the above equation. So as you can see 0.5mm2 cable is ample. Regards. Richard. Link to comment Share on other sites More sharing options...
rlubikey Posted September 5, 2016 Report Share Posted September 5, 2016 Depending on whether you think there might be some other things to do, you might consider buying an old wiring loom. That way you have all the colours and you're replacing like with like. Cheers, Richard Link to comment Share on other sites More sharing options...
Guest Posted September 5, 2016 Report Share Posted September 5, 2016 Richard. The problem with buying an old wiring loom is that it's an unknown quantity in relation to wire degradation. Personally, I would rather pay for new wire, especially thin wall which is a pleasure to work with and use. In addition you can obtain any colour combination you require. Regards. Richard. Link to comment Share on other sites More sharing options...
Pete Lewis Posted September 5, 2016 Report Share Posted September 5, 2016 Thin way is the way to go, if you use a lot it saves some weight as a bonus, as I acquired miles of cable on reels when the factory stopped production I have to admit to using all the wrong colours when needed , but tag and label these in the hope I remember in the future but I have some nice bright colours in a couple of odd places , you dont need to squint to confirm the colour code all good fun pete Link to comment Share on other sites More sharing options...
Guest Posted September 5, 2016 Report Share Posted September 5, 2016 Hello Pete. You are not alone on incorrect colour choices, I'm sure we have all been there at some stage. In fact I know a chap who only uses black and red wire for many of his wire runs. He says he never has a problem tracking the correct wire down, mmmmmmmm I'm not so sure !! However, on a more solid footing this will be of assistance to a lot of classic car owners, not just us with Triumphs and it is the BS-AU7 wiring colour standard code; which you probably know of very well Pete, in fact it's now the BS-AU7(a) system with the addition of yellow and slate base wires. I've attached a copy which hopefully will assist; it does make you use the correct colours !! Regards. Richard. BS-AU7 - LUCAS WIRE COLOUR CODES.pdf Link to comment Share on other sites More sharing options...
Guest Posted September 5, 2016 Report Share Posted September 5, 2016 Robin. You will see from the attached chart that the L & R indicators have their own trace wire. Green/ Red for the left and Green / White for the right. Regards. Richard Link to comment Share on other sites More sharing options...
Pete Lewis Posted September 5, 2016 Report Share Posted September 5, 2016 Very useful thanks , that should enlighten many printed off and added tot the file as the grey matter seems to remember lots but , this is brill to refer back too Pete Link to comment Share on other sites More sharing options...
dougbgt6 Posted September 5, 2016 Report Share Posted September 5, 2016 I never new there was a spec. Very interesting! I'll have to replace some of my brown, blue and yellow (with a green strip) wires. That's a joke, obviously. Link to comment Share on other sites More sharing options...
moretonjr_4430 Posted October 28, 2016 Report Share Posted October 28, 2016 Hello! I'm thinking of changing the wiring loom on my Spitfire Mk3 and I would appreciate advice / comment. Rimmer sell the Part Number RL1393 for £335 including VAT whereas Auto Sparks sell, what sounds the same loom, for £306 including VAT. That's quite a price difference especially as I'm having a fair amount of work done on the car and want to save a much money as possible. So, am I comparing apples with apples? Thanks, JM Link to comment Share on other sites More sharing options...
Darren Groves Posted October 28, 2016 Report Share Posted October 28, 2016 Autosparks are excellent, they probably supply Rimmers anyway hence the price difference. I've had several harnesses from them over the years, all excellent quality. Link to comment Share on other sites More sharing options...
Guest Posted October 28, 2016 Report Share Posted October 28, 2016 JM. Darren is spot-on. Rimmers collect items and sell at an inflated price. In fairness they do a good service and are willing to price match on many items. If anybody is going to the NEC in November and is thinking of purchasing anything from Rimmers, they will take the item to the show for collection and of course saves postage for the purchaser. Regards. Richard Link to comment Share on other sites More sharing options...
moretonjr_4430 Posted October 28, 2016 Report Share Posted October 28, 2016 Thanks chaps. May I ask an unrelated electrical question but I've stumbled across a company by the name of James Paddock Limited who also appear to be much cheaper than Rimmer for items such hood, carpet sets and clutch & brake cylinder. Again, any advice/comments? James Link to comment Share on other sites More sharing options...
AidanT Posted October 28, 2016 Report Share Posted October 28, 2016 I use paddocks most of the time as their prices are generally better and they have free delivery over ten pounds. Just be aware though the prices shown are exc vat. Aidan Link to comment Share on other sites More sharing options...
dougbgt6 Posted October 28, 2016 Report Share Posted October 28, 2016 I've bought stuff from Paddocks and they are fast and reliable. I bought a steering column end bearing seal and cap, the pictures were the wrong way around but I don't hold it against them as no one else stocked them! Canley are cheap and do good diagrams. Rimmers are reassuringly expensive, the Waitrose of Triumph spares. Link to comment Share on other sites More sharing options...
moretonjr_4430 Posted October 29, 2016 Report Share Posted October 29, 2016 Thanks for all your comments and tips; always thought Rimmer are expensive so hopefully I should save a few quid getting my Mk3 back into shape. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now