Danwedges Posted September 3, 2018 Report Share Posted September 3, 2018 My car seems to be running okay so I cleaned my plugs last week to check the colour so after 100 miles this is the colour of them and was wondering should I lean the mixture off? The outer ring is black with carbon but the centre and electrode is virtually uncoloured I've always been told to aim for a tan/brown colour and these plugs are making me think it's rich and lean at the same time? What's your opinion? Thanks Link to comment Share on other sites More sharing options...
Paul H Posted September 3, 2018 Report Share Posted September 3, 2018 Hi Dan - not wishing to crash your thread ive just checked my plugs and was about to ask for opinions - I feel my mixture is a tad on the lean side - too lean or about ok ? Paul Link to comment Share on other sites More sharing options...
poppyman Posted September 3, 2018 Report Share Posted September 3, 2018 This might help. Tony. Link to comment Share on other sites More sharing options...
Danwedges Posted September 3, 2018 Author Report Share Posted September 3, 2018 I personally think yours look closer to correct than mine but defiantly on the leaner side of good where as mine may be on the richer side? Link to comment Share on other sites More sharing options...
dougbgt6 Posted September 3, 2018 Report Share Posted September 3, 2018 Pleased to see they're including red coating, as in picture 2, this is caused by using fuel additive. I was surprised to find mine had turned pink and moving towards red. I stopped using additive after Uncle Pete told me about the "memory of lead" and my plugs eventually went back to picture 1. The plug in the first pictures do look a little red, but running rich. Second set a gnats too lean? Doug Link to comment Share on other sites More sharing options...
Pete Lewis Posted September 3, 2018 Report Share Posted September 3, 2018 If your gnats lean then some legs are shorter on one side , bit like a haggis, Dan too rich take the adjuster up 1/2 turn and retest what fuel do you use , low grade 95 ron ul can be sooty if running retarded Paul leave alone , Doug Glad you out of pink Pete Link to comment Share on other sites More sharing options...
Danwedges Posted September 3, 2018 Author Report Share Posted September 3, 2018 I've adjusted 1/4 turn would you recommend another 1/4? Or should I leave as is and check next weekend? I usually do about 100 miles a week and it only ever sees shell v power as anything else seems to run flat and cause overrun. I stopped using fuel additive a few months ago after reading about lead memory so maybe the red colouring will disappear after a few more months Link to comment Share on other sites More sharing options...
Pete Lewis Posted September 3, 2018 Report Share Posted September 3, 2018 Thats fine , recheck any signs of soot after a cruise give it some more In town driving with acceleration beeing frequent will give a sooty plig as the dashpots give you a rich mix when you open the throttles Only check plug colours after a steady cruise open road drive , Not hacking around the town Pete 1 Link to comment Share on other sites More sharing options...
Danwedges Posted September 3, 2018 Author Report Share Posted September 3, 2018 I have a 6 mile journey from work mainly on a motorway is this enough to give a proper colour on the plugs to represent the mixture? If so I can check and adjust in the morning when I get home from work Link to comment Share on other sites More sharing options...
dougbgt6 Posted September 3, 2018 Report Share Posted September 3, 2018 Pete, I thought you liked me in pink? Guys, have you tried "colour tune" very satisfying getting the mixture to burn blue. Doug Link to comment Share on other sites More sharing options...
Danwedges Posted September 3, 2018 Author Report Share Posted September 3, 2018 I had bother the last time I used the colour tune on mine showing flashing yellow on idle and white at higher revs which I put down to the air filters flowing too much air which was causing a flat spot at 3500 under load but this has been cured with velocity stacks inside the air filters and the top half of the filters taped off to reduce air in but I haven't checked with the colour tune since so probably a good idea I'll have to dig it out of the back of the garage Link to comment Share on other sites More sharing options...
Nick Jones Posted September 3, 2018 Report Share Posted September 3, 2018 Plug colour is only a useful guide if checked after a good hard run (some would say should be done by cutting the engine from cruise and coasting to halt!). To indicate what is possible with these old engines, when fitted with modern(ish) electronic injection, correctly set-up, the plugs will be almost completely clean and deposit free even after thousands of miles. The engine in the pic was a fairly heavy oil user too as can be seen from the head deposits. Link to comment Share on other sites More sharing options...
Nick Jones Posted September 3, 2018 Report Share Posted September 3, 2018 10 minutes ago, Danwedges said: I had bother the last time I used the colour tune on mine showing flashing yellow on idle and white at higher revs which I put down to the air filters flowing too much air which was causing a flat spot at 3500 under load but this has been cured with velocity stacks inside the air filters and the top half of the filters taped off to reduce air in but I haven't checked with the colour tune since so probably a good idea I'll have to dig it out of the back of the garage The problem with Colourtune is that it was originally intended for fixed jet engines where the idle mix setting was just that and didn't affect running elsewhere. On Strombergs and SUs the mixture setting affects the whole range and these engines idle best slightly rich, so the needles are factory selected for this. Therefore, to get the blue colour at idle you end up leaning it off too much and getting poor running/flat spots further up. MoT emissions adjustment tend to result in the same effect making it necessary to richen things up a bit after the magic paper is issued. You may get better results with colourtune if you treat the point at which the flame goes blue as a marker point and then richen back up a couple of flats until it just goes orange again. Blanking off part of the airfilters is an.......um..... unusual approach. If you have fitted aftermarket "free flow" air filters such as K & N and perhaps have exhaust mods too, you actually need different needles to compensate for the extra gas flow through the engine. Nick Link to comment Share on other sites More sharing options...
Danwedges Posted September 3, 2018 Author Report Share Posted September 3, 2018 The carbs are off my 2500 engine that were running fine but it threw a rod and I replaced it with a 2000mk2 saloon engine and the same setup for this leaned out excessively on the smaller engine which was the exact opposite to what I was expecting but being hif carbs I couldn't try a standard airbox so that was the only way I could think to restrict airflow a bit with what I had in the garage and it actually worked haha Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now