blubayou Posted September 7, 2021 Report Share Posted September 7, 2021 As above really, my spring is original and definitely sits too low causing clearance issues fully laden. I've always wanted it to sit a little higher so it sits level rather than pointing uphill. Reputable seller, £108 delivered. Apparently 45 have been sold, has anyone on here fitted one? Link to comment Share on other sites More sharing options...
Pete Lewis Posted September 8, 2021 Report Share Posted September 8, 2021 way back in the 2002 era we fitted a Moss decambered spring to the Vit6 to square up the \--/ it was terrible think it was made for a pram not a car it went up the tip next was a swinger kit equally as bad , final was a courier Pete Link to comment Share on other sites More sharing options...
blubayou Posted September 11, 2021 Author Report Share Posted September 11, 2021 Thanks Pete, Having dug a little deeper, Canley's list the Moss spring 159640 for earlier short driveshaft mk1Vs, long driveshaft models like mine as 159654, so I'll give it a miss. I may pull the rear spring out over winter and do something with it. Link to comment Share on other sites More sharing options...
blubayou Posted May 9, 2023 Author Report Share Posted May 9, 2023 (edited) Well, last time I fitted tap washers as I had them to hand. This time I have fitted new 'Bastuck' rubber buttons. They don't fit the depressions so had to trim them. Result is no improvement at all. I would like to lift the rear end 2" to be honest, anyone done this? Edited May 9, 2023 by blubayou Link to comment Share on other sites More sharing options...
johny Posted May 9, 2023 Report Share Posted May 9, 2023 Back in the day didnt people install the springs upside down to get round this problem? Link to comment Share on other sites More sharing options...
SpitFire6 Posted May 9, 2023 Report Share Posted May 9, 2023 Hi, Our American friends fit Air shocks to raise the height. Fully adjustable & from Amazon. Cheers, Iain. Link to comment Share on other sites More sharing options...
Unkel Kunkel Posted May 9, 2023 Report Share Posted May 9, 2023 (edited) I would suggest at least hesitate in changing or getting rid of your old spring. Although we tend to assume “ new” parts are always better than “old”parts, “T’aint necessarily so” in relation to these springs. New rear springs can vary in appearance, weight and dimensions and no doubt other areas.They don”t always solve problems. Replacing the spring “buttons” -( the between-the spring leaves- isolators) , can restore the car’s lost “back end stature “ effectively and very cheaply. The original rubber type can be replaced with far more effective and durable ones - Teflon, Nylon or UHWPE - see E- Bay. You can make them but it is a bit of a faff. Edited May 9, 2023 by Unkel Kunkel 1 Link to comment Share on other sites More sharing options...
johny Posted May 10, 2023 Report Share Posted May 10, 2023 Believe the OP has already tried this (see post above) and anyway he wants a 2" raise which is a lot to ask from new buttons.... Link to comment Share on other sites More sharing options...
Mjit Posted May 10, 2023 Report Share Posted May 10, 2023 That car does look a little low so assuming there's no lowering block fitted between the top of the diff. and the spring I'd say it's a well worn spring. I've no objection to buying from eBay...but (for example) James Paddock will sell you a 'long shaft' rear spring for more or less the same price (£97.50 + shipping + VAT) and I'd trust their after sales support more than a random eBay seller... Link to comment Share on other sites More sharing options...
Unkel Kunkel Posted May 10, 2023 Report Share Posted May 10, 2023 (edited) On 10/05/2023 at 06:50, johny said: Believe the OP has already tried this (see post above) and anyway he wants a 2" raise which is a lot to ask from new buttons.... I saw that but noted Blubayou had tried tap washers- which was imaginative, and then rubber ones - which didn’t fit. I was relating from experience regarding buying a new spring (from one of the major suppliers)as a cautionary tale as I was surprised and disappointed to find it was completely different spec with thicker leaves, very much heavier and didn’t fit into the space between the diff. and first leaf. I returned it and got a refund. So I re-used the original spring with UHMWPE spacers. inserting these “buttons” did give a noticeable increase in ride height ( any thickness you make them will be that x4 in ride height)- though if 2” is what is needed, that does seem a lot. Edited May 11, 2023 by Unkel Kunkel Link to comment Share on other sites More sharing options...
johny Posted May 11, 2023 Report Share Posted May 11, 2023 yes the first time he tried tap washers and the second Bastuck produced items but neither had the desired effect. I suppose he could get some specials made up but imagine there must be a limit on just how thick the buttons can be.... Link to comment Share on other sites More sharing options...
rlubikey Posted May 11, 2023 Report Share Posted May 11, 2023 (edited) Springs can sag over time, and the rubber buttons can squash or even fall out. But buying a new spring is a lottery - they will all differ a bit compared to the factory originals! There are 8 buttons I think - 4 each side and their effect on raising the car is additive (each one you swap or add, adds a bit more height to the car) plus there's a multiplying effect - the tip of the spring moves further than the leaf in the vicinity of the button you change. There was a thread about leaf buttons here, and Cliff.B added some Polyurethane buttons but I don't know which manufacturer's these were. The buttons seem quite thick to me - thicker than the rubber buttons - so they may have had a significant effect. Cliff.B says about 1/2" or maybe more. The alternative mentioned is air-assist shock absorbers. I have fitted the Monroe Max-Air MA785 which are intended for Corvettes (the car, not the ships) and certainly do the job. There's a thin pipe from each one, a joining tee (so they share the same pressure) and a Schrader valve you mount somewhere convenient (e.g. the boot) where you pump up the shocks to raise the back of the car by the desired amount. Sadly, one of my Monroes failed after a few years so I've converted back to bog standard. There is another company makes the same sort of shock - Gabriel Hijackers and you need part number 49304 for Spit rear. If you go down this route, note that you keep the bush from one end of your old shocks to replace the one that comes in the shock which fits the Corvette but not the Spitfire. I think that's it for now. Let us know what you decide to do and how you get on. Cheers, Richard PS: Cliff.B's PU buttons Edited May 11, 2023 by rlubikey Link to comment Share on other sites More sharing options...
blubayou Posted May 11, 2023 Author Report Share Posted May 11, 2023 Thanks all, some good ideas. In the short term I've ordered some of those Delrin buttons off ebay. I shall fit them and report back. I can definitely advise NOT to use the Bastuck items, my tap washers were far cheaper, fitted well and at least equally as good Really I could do with a replacement spring with a more pronounced arch but have yet to hear a good report on any modern replacement spring. I was considering heating the two lower leaves near the ends and bending them a little lower. Anyone done this? Link to comment Share on other sites More sharing options...
johny Posted May 11, 2023 Report Share Posted May 11, 2023 The heat treatment of the spring to get the correct temper is quite critical so any heating you do could leave the steel soft or brittle and prone to breaking.... Link to comment Share on other sites More sharing options...
Keith Nock Posted May 12, 2023 Report Share Posted May 12, 2023 I think this is what you need buy quality and buy once . I initially put a cheap new spring on the GT6 . and had problems bought a replacement from a reputable supplier I suspect it came for these people https://www.ebay.co.uk/itm/225395443279?epid=550067965&hash=item347a9d864f:g:PcIAAOSwExJXofAr&amdata=enc%3AAQAIAAAA0I3tLUa8x12LuckGrkUXQIDuvmnIDu7h1QIynXKr6KkHtDedf4%2Faox6ObOmqOYTE0VElN9Sd0IdsHEF%2FeqzhB8fNoFioPDYhOKc%2Bz0oG6c3DEXHz%2FbTrtBzj%2FUlHXwdHqD7vuLoMctkPb%2BAMoXv%2BNc6PC0EUmyBVbBEWth4Io7fjI%2Fx42PDesm%2F2pUvYps%2BP7plBHAURBc1jI1gu0aoNphmqvFgY7C%2Brsc%2BX07N%2BhmZXCnRRC2tsA2pBTSnvLAm%2FZ38LPagkB%2BIdLe96LpbYwOM%3D|tkp%3ABk9SR6SepeyBYg Regards keith Link to comment Share on other sites More sharing options...
Ian Foster Posted May 12, 2023 Report Share Posted May 12, 2023 (edited) I added an additional central leaf to my original rotaflex GT6 spring. I had tried a new spring but found it fairly hopeless. Owen Springs provide the new leaf (actually a pair and the other now resides in Nick's GT6) and all I had to do to accommodate it was to elongate the holes in the inner straps. It raised the rear ride height slightly and has increased the rear roll stiffness, which I felt always was an issue with the rotaflex spring. It has made a big difference to the handling of the car and the rear corner now doesn't dip when you turn in. With the swing spring design, this might be a bit more tricky, but anything is possible. Ian Edited May 19, 2023 by Ian Foster grammer Link to comment Share on other sites More sharing options...
blubayou Posted May 19, 2023 Author Report Share Posted May 19, 2023 (edited) Just fitted these Delrin buttons today. The new Delrin buttons did not fit at all, I had to file a chamfer on the top of each to get them flush to the metalwork. Hell of a job as getting the bundle back into the spring box is very very difficult. Had to release the fixed spring to get it all clamped up. Also had to glue the buttons in place to aid assembly. The longest leaf appeared to have no dimples to fit the buttons, but it does they were bunged up with the remains of the original rubber buttons. Edited May 19, 2023 by blubayou Link to comment Share on other sites More sharing options...
Unkel Kunkel Posted May 19, 2023 Report Share Posted May 19, 2023 (edited) That looks good! New springs do seem to vary in spec.- not just in the spring rate , but in curvature, weight, thickness of the leaves - and also the size of those ‘ dimples” for the buttons - insulators or whatever you call them.There were some aftermarket springs made with no buttons or recesses ie the dimples to hold them and the edges of the spring leaves in some cases were sharply cut. ie were’t chamfered . Those buttons closely resemble my DIY ones, except mine are UHMWPE Getting the “swing spring” secured in the spring “box” can be quite a wrestle. I battled with G clamps and various levers etc. for most of an afternoon. The tendency for the outermost buttons to fall out ceases once the drive shafts, shock absorbers etc are all connected up because as the lower leaf spring of the “swing spring” set up can’t then travel as far downwards. Edited May 19, 2023 by Unkel Kunkel Link to comment Share on other sites More sharing options...
blubayou Posted May 20, 2023 Author Report Share Posted May 20, 2023 Well got the spring fitted last night. Lowered to the ground, pushed car back & forth... It was awful. Sitting high but with around 2deg Positive camber, like a maladjusted Herald. This morning I was ready to take it off again, but decided to run it around the block to see if it would settle. Success! Looks good, sits an inch higher (approx 24" arch to floor, was just short of 23") and just over 1deg Negative camber Link to comment Share on other sites More sharing options...
Kevinrpayne Posted May 21, 2023 Report Share Posted May 21, 2023 I’ll add my 10 peneth to the saga of springs. I’ve fitted a Rimmer that was rubbish - Oils t go round corners without hopping next bought a UK made one and that was the other extreme. Unfortunately I had chucked the old one away - bad move this time I’ve bought a moss one that wasn’t quite as bad as the Rimmer but not far off but thankfully this time I learnt my lesson and I’ve mixed the two springs up and I have near on perfect ride height. If it sags then not a problem, I’ll just swap out an old leaf for a new one. I’ve got really good T swapping out springs now. The shop spring lifter really helps get one if you don’t have one Kevin Link to comment Share on other sites More sharing options...
blubayou Posted May 28, 2023 Author Report Share Posted May 28, 2023 After 70 miles the car is sitting well, better than it ever has. Totally standard factory fitted spring with Delrin Buttons from a bloke on ebay (BTUK) Approx 1/2 deg negative camber on unladen 1/2 full tank, long driveshafts. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now