Paul H

Set of 200 springs sourced from Ebay £6.25 deld - Arrived today . I will advise the Spring which fits the Slave push rod This will hopefully shut up the whistling canary coming from the gearbox housing Paul

If using R9 use vaseline when joining to metal as reduces slivers Paul

Welcome aboard Paul

Hi Dave where did you source the spring Paul

I have a spare vitesse tank which has been sealed with POR 15 tank treatment PM me if you want futher info Paul

Sorry Pete. Senior moment plus so excited about finding a bargain. Looking in the correct forum page i see i wasnt the first to find it Paul

What will the quality be like ?? £18 delivered Ebay Link looking for the classic look for my Vitesse - seen similar at more than twice the price and more than £200 for new replica Classic radios - Do you get what you pay for ? Paul

Multimeter arrived today and all working plus battery was included £5.55 delivered including battery !!!!!! Paul

My Vitesse has developed the Chirrup noise coming from the gearbox housing, checked and with pressure on the clutch whilst driving it stops - i did observe that with deceleration the canary is more audible - the slave cylinder is a NOS and only been in for 3 months . Is it feasible to use 2 springs in the Slave Cylinder ? Paul

Hi all , thanks for informative replies - Checked my Vitesse this morning and the inline filter by the carbs was 3/4 full which theoretically means she will fire - Air temp- was 7 degrees C so pretty cold - 3 turns no joy so added a squirt of carb cleaner in both rubber air extension tubes and next click she was away . So thinking now its the lazy starter which might be overcome by buying a HiTorque starter which from reports ive seen have a design fault with water ingress so not going down this route - For the time being will add a NRV before the pump ( thanks Pete ) I dont expect this to improve matters though for the cost Id like to be proved wrong. So added Carb Cleaner to my list of tools carried Paul

I like this one as uses PP3 whereas my dead Hilka uses an obscure 12v A23S + there is no auto switch off . Maybe its more than 15 years old Paul

Hi steve Temp and time not on my list Paul

Hi my Hilka Multimeter has died after 15 years and its not the battery - looking for a replacement - Not looking for anything too technical as only basic functions used so is this one ok or should I spend a bit more £ Thanks in advance

Hi Pete - thanks for info , didnt twig about primer and cam position - Ive changed all tubing to R9 and top hose to tank is secure - Ive got the T Shirt for Slivers so have filters after the fuel tank after the pump and before the carbs and when she fires up were fine - I think it will be the pump valves which I replaced and possibly they are not set properly and leaking - The replacement valves went in easily and might be leaking so I will go down the route of a one way valve which will be fitted after the pump - thanks for the link NB Choke is getting full travel Paul

Hi , after a week or so layoff my Vitesse wont start - 7 or 8 tugs no joy - then a puff of carb cleaner in the air filter extension tubes and she starts. Then she will start 1st go all the time - The following day again no issues - 1 week and she wont start . I have a fuel filter close to the carbs and noticed the level drops after a few days so think this is the issue - Is there such a thing as a one way valve stopping the fuel running back - I can see no obvious leaks and there is no petrol small - the carbs arent leaking either - Any thoughts would be appreciated . The starter motor seems a bit lazy which could be the issue - It was new when I bought the car & the battery is new + ive added a direct earth from the starter to the battery and the battery is on permanent charge using a CTEK charger . The pump has had a new diaphragm + valves and the primer works though after a week I prime though cant get enough fuel through to start which sounds strange . Incidentally the fuel filter level in the pic indicates the car will start on first tug Paul

Hamilton are very good , used one myself . Breathable and long lasting - Check this link before buying check with TSSC club Shop ( assuming you are a member ) as you should get a discount - I did and the cover was delivered direct from Hamilton Hope this helps Paul

Welcome aboard - you are in the right place - ATU6M looks like its gone to rust heaven Paul

Done

Sold for £1750 , good deal for somebody Paul

There is a note on FaceBook today re Survey Paul

Just noticed the Vitesse is on Ebay currently £210 - click here Paul

Luckily for me it works, just needs a clean up Paul

Agree price is way too high - I paid £7.60 for mine from Ebay - condition unknown Paul

Hi Pete , you were correct under the paper sticker it says Smiths etc but no codes / model number etc - here are the pics . Plan to dismantle and clean so should be able to show more internal pics UPDATE - just taken off the glass and there is a mark BV2213/00 - does this help ? Paul

Hi Pete , thanks for info - just a white label on the back with 247 Paul