-
Posts
3,180 -
Joined
-
Last visited
-
Days Won
28
Content Type
Profiles
Forums
Blogs
Gallery
Downloads
Store
Events
Everything posted by Paul H
-
Thanks for the link ,looks like I’ve purchased the correct 2k thinners , also using cellulose from the club shop Paul
-
Hi Alex , I did it on my own so keep at it . The springlifter must be at max height and a scissor jack under the link , then to align use a Pointed chisel etc Paul
- 13 replies
-
- rotoflex
- reassembly
-
(and 1 more)
Tagged with:
-
Hi , this is the way I did , I’m sure there are others , all in all it’s a pig of a job . Good luck Paul
- 13 replies
-
- rotoflex
- reassembly
-
(and 1 more)
Tagged with:
-
What 2k primer are you using . I’ve just purchased HB Body 989 2k Epoxy Primer based on recommendation from the mig welding forum , are you top coating with 2k or Cellulose. Paul
-
Welcome to the forum . Reassembling rotoflex assembly is very difficult . Check this forum link and read through the posts and you should find some good advice . Page 2 is where you will find help Paul
- 13 replies
-
- 1
-
- rotoflex
- reassembly
-
(and 1 more)
Tagged with:
-
I thought my mk2 vitesse HC xxxxx had flat piston heads as when testing for TDC with the plugs out and a screwdriver in I couldn’t detect a dome section . If it is domed would there be a telltale tab in the gasket rear Paul
-
Thanks Nigel , so my mk2 vitesse HC xxxx has domed pistons ? Paul
-
Yes I’m interested in the bonding application for my Vitesse , both sides of bonnet where the locking mechanism is are poor . Fibreglass cracks appearing . Bonding in a new stepped section and skimming with filler is now worth investigating Paul
-
Newbie ? Theres a part finished engine for a GT6 on EBay https://www.ebay.co.uk/itm/Triumph-GT6-Vitesse-2000-Engine/333668365572? Question 1 the pistons are domed so this engine is from Triumph 2000 ? ME Series ? Question 2 The seller says cost effective route is to resleeve 2 of the pistons , can u Resleeve Paul
-
Can’t help with the thread gauge other than mine was secondhand from Spitfire Graveyard and was originally from a Spitfire . Here’s a pic of my setup on my Mk2 Vitesse Paul
-
You should sell your headlining on EBay , it would sell well Paul
-
-
-
Progress : the door has been rubbed down and filled , the scratch and surface rust areas treated . I’ve progress from 140 grade up to 400grade wet n dry , Just one coat of primer to see if the surface finish is ok ie covering the remaining surface blemishes . I’m happy with the result so far , a few small areas need more work .Next the remaining areas will be prepared with 400 grade and the next coat of primer will go on . One ? How can you tell if the door skin is original . On mine there is some braze welding at the top seal by the hinge plus the odd small weld on the side Paul
-
If you opt for the suspension mod remember they are handed . When I purchased mine they were the same and had to be exchanged Paul
-
Progress: Checking out the inside of the door found surface rust by the window channel and surrounding areas about 6 ins range . Wire brushed and treated with Bilthamber Hydrate 80 , and now Bilthamber Electrolux ( zinc based primer ) Next coat will be spray can black from Toolstation . Final coating for all the inside will be Bilthamber Dynax s50 which has a 360 wand extension . The door base and lower half still has the factory under seal and pretty much intact . Any breaks in the underseal will be filled in by the Dynax . The chrome trim had been removed and the rusty retaining rivets drilled out .Not sure of the spec and where to purchase When I was stripping out the mechanicals there were signs that I wasn’t the first to strip , bolts instead of posidrive screws and no poly sheeting attach to the window base . On clearing out the debris I found small fragments of shattered window . Paul
-
Hi Dave I can’t find the claw button holder anywhere so probably going to use this mod , painted of course Paul
-
The door is now fully stripped to component parts with the quarter light out and top rivet removed . Next job is to kill the internal rust in the door and add a protective coating using Bilthamber products though not sure which products to use yet The rear window channel has a layer of felt which is passed its best. Any ideas where this can be sourced ? Paul
-
I have moved to the Huco pull pump which sits alongside the battery in my Vitesse and it’s been a good move . If you consider this as a possibility I’ll dig out the specs and let you know Paul
-
https://www.gumtree.com/p/car-replacement-parts/hub-caps-for-triumph-herald/1378623552 Ash Hampshire Paul
-
Nut sliced and cutting , cleaning thread on the way down . Need to check the thread next . Re the top pivot I was going to drill out Paul
-
Painting , hopefully rubbers are ok as new ones apart from being expensive don’t fit well . I’m going to hacksaw the nut now Paul
-
Canleys sell the silent channel , the rear channel looks like its felt glued in so no metal framework Paul
-
Got the QL out in the end. Seen Rarebits FB and channel isn’t there . Replacement will be necessary . If I cannot remove intact the spring assembly on the air conditioning window what are the options. Paul