Colin Lindsay Posted April 1, 2020 Report Share Posted April 1, 2020 13 hours ago, ahebron said: But why does the diff look shiney? Looks like a plastic bag tied round it? (I have to make up for not spotting the missing floor by spotting something else...) Link to comment Share on other sites More sharing options...
ludwig113 Posted April 1, 2020 Report Share Posted April 1, 2020 17 hours ago, ahebron said: Like Colin not till you mentioned it🙄 But why does the diff look shiney? it's one of those new polished diffs....... err no, it's just a plastic bag as i was doing alot of cutting and grinding. Link to comment Share on other sites More sharing options...
yorkshire_spam Posted April 3, 2020 Report Share Posted April 3, 2020 How about this spanner? It has a very specific purpose in my garage: Link to comment Share on other sites More sharing options...
dave.vitesse Posted April 3, 2020 Report Share Posted April 3, 2020 A right hand spanner Link to comment Share on other sites More sharing options...
JohnD Posted April 3, 2020 Report Share Posted April 3, 2020 Is that a 17mm? I have set of 8 and 10mm spanners like that, I cut off the heads and welded them back at an angle, that I use to adjust the length of the drop arms on my non-standard Pi throttle actuators. So, I assume this is for some difficult-to-access nut, or plug. But much bigger. I also have an altered spanner for the front nut that secures the exhaust manifold. The standard is too long, but when cut down, it's had on the hands to get it tight, so I've wrapped it in a length of copper pipe. That might suit a 17mm? The tape covers where the pipe is secured to the spanner by wiring. John Link to comment Share on other sites More sharing options...
poppyman Posted April 3, 2020 Report Share Posted April 3, 2020 29 minutes ago, dave.vitesse said: A right hand spanner Anyone can see it's a left hand one Link to comment Share on other sites More sharing options...
yorkshire_spam Posted April 3, 2020 Report Share Posted April 3, 2020 19 minutes ago, JohnD said: Is that a 17mm? Yep it is. Link to comment Share on other sites More sharing options...
JohnD Posted April 3, 2020 Report Share Posted April 3, 2020 But not for the manifold? Link to comment Share on other sites More sharing options...
yorkshire_spam Posted April 3, 2020 Report Share Posted April 3, 2020 2 minutes ago, JohnD said: But not for the manifold? It's for adjusting the mixture on the HS4s fitted to my Spitfire, it has to "dodge" the heatshield and the silly air filter things. It's oversized, which allows a bit of wiggle room around various obstructions, but is a tight enough fit to turn the adjuster without "skipping" Link to comment Share on other sites More sharing options...
JohnD Posted April 3, 2020 Report Share Posted April 3, 2020 My throttle adjusters weren't far wrong then! I love to see 'altered' tools! And specialised tools. My favourite examples are the mortice chisel, which has a square blade, so that it can be used as a lever to scrape out chips from the bottom of a mortice cavity, and the glaziers hacking knife, a heavy bladed instrumetn with a wide back. It is designed to be used with a hammer, to remove old putty from a frame: 1 Link to comment Share on other sites More sharing options...
Bfg Posted April 4, 2020 Author Report Share Posted April 4, 2020 ^ Thanks John, I found something very similar to that glazier's knife in the bottom of an old tool box. Never could find a use for an extra thick bladed blunt knife with a taped up wooden handle. Now I know I never will Link to comment Share on other sites More sharing options...
Mathew Posted April 5, 2020 Report Share Posted April 5, 2020 A little rust remover. Lookup on internet as I don't want the blame if it goes wrong!!🤕 . Been on a low current for 24 hours. Will check it later to see if it worked VID_20200405_113521.mp4 Link to comment Share on other sites More sharing options...
Colin Lindsay Posted April 5, 2020 Report Share Posted April 5, 2020 That reminds me.. must go check the soup. Link to comment Share on other sites More sharing options...
AndyTV8 Posted April 5, 2020 Report Share Posted April 5, 2020 Not homemade, but maybe of use to someone...... for years I have always struggled to get a good seal on my grease gun, despite my best endeavours and using cloth over the grease-nipple I always seemed to get only 10% where it was intended and mess elsewhere! I spotted this on special offer a while ago on amazon, used it this afternoon and it was a revelation - all grease in the right place, job done in seconds. https://www.amazon.co.uk/G-COUPLER-Coupler-Lock-Clip-off-machine/dp/B0133NDH6E not cheap for what it is, but I suspect it will pay for itself in reduced grease consumption and fewer swear-box contributions! ....... Andy Link to comment Share on other sites More sharing options...
JohnD Posted April 6, 2020 Report Share Posted April 6, 2020 "So, seeking for further amusement" I reviewed my files and found this: This piston stop is easily made from a piece of square/rectangular tube, or some angle iron. It will allow you to find more accurately the TDC than is possible with a dial guage. If you want to do the job without removing the head studs, then two lengths of tube with washers on top, will secure the stop in place over the studs. Jphn PS "Seeking for further amusement" Stanley Holloway, may amuse you. His version of "Albert and the Lion" is famous, and he did many others, for instance "Sam Small" 1 Link to comment Share on other sites More sharing options...
yorkshire_spam Posted April 6, 2020 Report Share Posted April 6, 2020 2 hours ago, JohnD said: This piston stop is easily made from a piece of square/rectangular tube, or some angle iron. I like that one John, I spent ages beggaring around trying to find TDC using a dial gauge it took something like 6 or 7 itterations to hone it down to a position I had any confidence in. When I re-checked it using a piston stop I was about 2 degrees out. Link to comment Share on other sites More sharing options...
JohnD Posted April 6, 2020 Report Share Posted April 6, 2020 Easily, or rather not easily, done! Link to comment Share on other sites More sharing options...
yorkshire_spam Posted April 6, 2020 Report Share Posted April 6, 2020 18 minutes ago, JohnD said: Easily, or rather not easily, done! I think the problem with the dial gauge method is that you need to note the point at which it stops moving and then when it starts again and then find the mid-point, which means you have to be turning to to find those points, which is pretty much impossible to do smoothly and reliably IMHO. I had similar issues but nowhere near as bad setting the cam timing as you have to identify the point of max lift on #1 inlet. Link to comment Share on other sites More sharing options...
Pete Lewis Posted April 6, 2020 Report Share Posted April 6, 2020 on the stanley hollaway dad had on 12" 78s Albert comes back, the magna carta, marksman sam , battle of hastings we need some funnies these days All the much-loved characters such as Albert Ramsbottom (‘with a stick with an ‘orse’s ‘ead ‘andle’), Sam Small (‘Sam, Sam, pick oop tha’ arm), and King ‘Arold (‘on his ‘orse with his ‘awk in his ‘and’) are legends Pete Link to comment Share on other sites More sharing options...
JohnD Posted April 6, 2020 Report Share Posted April 6, 2020 Sad to say, Pete, legends but nowadays, lost. The comic monologue is a lost art. Link to comment Share on other sites More sharing options...
Mathew Posted April 6, 2020 Report Share Posted April 6, 2020 On 05/04/2020 at 11:42, Mathew said: A little rust remover. Lookup on internet as I don't want the blame if it goes wrong!!🤕 . Been on a low current for 24 hours. Will check it later to see if it worked VID_20200405_113521.mp4 Before and after pictures Link to comment Share on other sites More sharing options...
Mathew Posted April 6, 2020 Report Share Posted April 6, 2020 Tool for holding diff flange 1 Link to comment Share on other sites More sharing options...
ahebron Posted April 7, 2020 Report Share Posted April 7, 2020 (edited) This will allow me to support the car on the wheel jacks when I have a wheel removed for longer than a day and can move it back to its stored place. Thats so I can repack the garage and get everything back in its place. Its a lot safer then placing blocks of timber across the bars of the wheel jack. Edited April 7, 2020 by ahebron Reattach photos 1 Link to comment Share on other sites More sharing options...
Bfg Posted April 7, 2020 Author Report Share Posted April 7, 2020 Just seen this on the TR forum, posted by Bob (LeBRo) and thought it was a good enough idea to share here . . Bob writes " Following a suggestion from Hamish, today I made an adapter out of an old spark plug to allow me to inject compressed air into the pot. So took rocker box off, turned engine till No. 2 rockers were rocking, so that I knew both valves on No. 3 will be closed. (yes there was clearance between valves & rockers) inject air at approx 50 PSI and lo & behold lots of air exiting from the exhaust (none from carbs)." Thanks Bob / Hamish .. I'd not seen that one before. Pete. Link to comment Share on other sites More sharing options...
yorkshire_spam Posted April 7, 2020 Report Share Posted April 7, 2020 12 minutes ago, Bfg said: Just seen this on the TR forum, posted by Bob (LeBRo) and thought it was a good enough idea to share here . . Bob writes " Following a suggestion from Hamish, today I made an adapter out of an old spark plug to allow me to inject compressed air into the pot. So took rocker box off, turned engine till No. 2 rockers were rocking, so that I knew both valves on No. 3 will be closed. (yes there was clearance between valves & rockers) inject air at approx 50 PSI and lo & behold lots of air exiting from the exhaust (none from carbs)." Thanks Bob / Hamish .. I'd not seen that one before. Pete. Pete, I've seen something very similar before, but used for changing valve springs in situ rather than testing valves etc. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now